Getting Started GuideRead this manual first and retain for future reference.
9 • Keep the power cord away from a heat source; failure to do this may cause the power cord coating to melt, resulting in a fire or electrical shock.
10 • Be careful when handling the main board, expansion board, RAM, and ROM. Touching the edges or a sharp portion of the main board, expansion board
11 • The fixing unit and its surroundings (including the output area and the staple cartridge for LBP5975) inside the printer are hot during use. When
12 Introducing Your Print System In addition to its standard features, listed in User's Guide, you can add the following options to expand yo
13 Step1 Taking the Printer Out of the Package and Installing the PrinterConfirming the Contents of the BoxMake sure that all the following items are
14Step11Carry the printer to the installation site.Carry the printer with 4 or more people by holding the lift handles on the lower portion of the pri
15Step1Be sure to install the printer on a sturdy platform that can easily support the weight of the printer and optional accessories. Do not install
16Step1• LBP5970 (6 locations)IMPORTANTDispose of the packing materials according to local regulations.NOTERemove the tape that secures the rear cover
17Step14Tilt the fixing unit toward you.While pressing the green lock release buttons (A) on the left and right side of the fixing unit a, hold the tabs
18Step17Close the front cover.While supporting the front cover a, push and close the front cover with both hands as shown in the figure b.CAUTIONPush t
1 Color imageRUNNERLBP5975/5970Getting Started Guide Contents Preface... 2System Configurat
19Step19Remove the tape shown in the figure.10Remove the packing material inside the paper cassette.IMPORTANT• A packing material is attached to the pa
20Step1After lifting the front of the paper cassette up a little b, push the paper cassette into the printer firmly until the front side of the paper c
21Step2Connecting the Power CordIMPORTANT• One AC power outlet should be used exclusively for the printer.• Do not plug the power plug into the auxili
22Step3Installing the Drum CartridgesFor details on how to handle the drum cartridges, see "Chapter 6 Routine Maintenance" in User's
23Step32Tilt the fixing unit toward you.While pressing the green lock release buttons (A) on the left and right side of the fixing unit a, hold the tabs
24Step3• The installation positions of the drum cartridges are arranged in order of Yellow, Magenta, Cyan, and Black from the back as shown in the figu
25Step38Remove the packing material attached with tape (B) (1 piece) shown in the figure.Remove the tape a and packing material at the same time. If th
26Step312Hold the blue tabs (A) of the drum cartridge and shake it up and down 10 to 12 times each as shown in the figure to evenly distribute the deve
27Step314Pull the sealing tape (approx. 28 in. (70 cm) long) out gently and horizontally while supporting the drum cartridge.When pulling the sealing
28Step316Make sure that the levers (A) near the drum cartridge guides on the both sides are in the proper position as shown in the figure.If the levers
2 Preface Manuals The manuals for this machine are divided as follows. Please refer to them for detailed information. Getting Started Guide (this m
29Step318Make sure that the levers near the drum cartridge guides on the both sides are in the proper position as shown in the figure.19Make sure that
30Step3● LBP5975By pressing the top cover with both hands, close it firmly until it cannot be pressed down any further as shown in the figure.IMPORTANTT
31Step324Close the front cover.While supporting the front cover a, push and close the front cover with both hands as shown in the figure b.CAUTIONPush
32Step4Installing the Toner CartridgesFor details on how to handle the toner cartridges, see "Chapter 6 Routine Maintenance" in User'
33Step43Take the toner cartridge out of the package, and then take it out of the protective pack.While holding the center portion on the top of the pr
34Step4Insert the toner cartridge so that the orientation of the character on the toner cartridge and that on the toner cover match.6Tilt the lock rel
35Step5Loading Paper in the Paper CassetteFor details on handling the multi-purpose tray or paper cassette, see "Chapter 3 Loading and Outputting
36Step51Pull out the paper cassette.Pull the paper cassette out until it stops a.● After lifting the paper cassette up a little b, pull it out while s
37Step5● While holding the lock release lever of the rear paper guide a, slide the guide to the mark for the size of the paper to be loaded b.● While
38Step5-When loading paper in landscape orientation, such as when loading A4,B5, A5, Letter, or Executive size paper, load the paper so that theprinti
3 Abbreviations Used in This Manual In this manual, product names and model names are abbreviated as follows:Microsoft Windows 2000: Windows 2000Micr
39Step5The default is "LTR".IMPORTANTMake sure that the size of the loaded paper matches that of the paper size setting switch before settin
40Step6Connecting to a ComputerThis section describes how to connect the printer to a computer and network.This printer is equipped with a LAN connect
41Step62Connect the other end of the LAN cable to the hub.IMPORTANTThe supplied CD-ROM does not include the printer driver for Macintosh. Download the
42Step61Make sure that the printer and computer are OFF.2Connect the B-type (square) end of the USB cable to the USB connector on the rear side of the
43Step7Turning the Printer ON and Checking the Printer OperationThis section describes the procedures for turning the printer ON and checking the prin
44Step7Checking the Operations with Configuration Page PrintBefore using the printer for the first time, be sure to perform Configuration Page Print to c
45Step7When the Printer Does Not Operate ProperlyIf the printer does not operate even after turning it ON or print Configuration Page Print properly, t
46Step71Press [Settings].2Select CONTROL MENU using [ ] and [ ], then press [OK].3Select PANEL LANGUAGE using [ ] and [ ], then press [OK].4Select the
47Step71Make sure that the Job indicator is off.2Press " " of the power switch on the printer.When Using a Hard Disk (Only When a Hard Disk
48Step74When the message <TURN OFF POWER> appears, press "" of the power switch on the printer.
4 System Configuration Requirements for Using User Manual CD-ROM The User Manual CD-ROM Menu is software that enables you to select and view PDF Manu
49Step8Installing the Optional AccessoriesOptional AccessoriesThe following optional accessories are available in order to make full use of the printe
50Step8NOTEBe sure to use a 3.3V DDRAM DIMM compatible with this printer as the expansion RAM module. It is recommended that you should use Canon Expa
51Step8Wireless Network Interface Board NB-W2NB-W2 is an interface board to be installed in the expansion slot of the printer.The communication mode s
52Step8IMPORTANTDo not touch the connector (A) or feed rollers (B) in the paper feeder. This may result in damage to the printer or misfeeds.NOTE• Up
53Step8Moving the PrinterWhen installing the paper feeder in the printer after installing the printer, move the printer to an appropriate location tem
54Step8After lifting the paper cassette up a little b, pull it out while supporting it with the other hand in the figure c.IMPORTANTThe paper cassette
55Step8-LBP5975-LBP5970IMPORTANTMake sure that the front cover and multi-purpose tray are closed before carrying the printer.Installing the Paper Feed
56Step81Remove the tape that secures the paper cassette and cassette protective cover.2Remove the packing materials shown in the figure in order of a a
57Step8While holding the paper cassette with both hands, pull it out completely d as shown in the figure.IMPORTANT• Because the paper cassette is heavy
58Step8• Do not touch the feed roller (A) in the paper cassette. This may result in misfeeds.• Dispose of the packing materials according to local reg
5 Installation Site Installation Environment In order to use this printer in a safe and comfortable manner, install the printer in a place that fulfil
59Step8IMPORTANT• Do not touch the connector (A) or feed rollers (B) in the paper feeder. This may result in damage to the printer or misfeeds.• Do no
60Step810Gently set down the printer unit while matching the positioning pins (A) on the paper feeder.11Fix the printer unit and paper feeder with the
61Step812Attach the cassette protective cover.While pressing the levers of the cassette protective cover, insert the projections into the slot on the
62Step81Turn the printer and computer OFF a, remove the USB cable b, and then disconnect the power plug from the AC power outlet c.2Remove all the int
63Step8Raise the slot cover a little b, then remove the slot cover in the direction of the arrow c.IMPORTANT• Do not touch the main board parts, print
64Step8Align the notch (B) with the RAM slot as shown in the figure a, and then insert the RAM module completely into the slot b.When the RAM module is
65Step89Attach the rear cover a, then slide it b as shown in the figures.10Connect the interface cables except for the USB cable, and connect the power
66Step8-Do not touch the hard disk parts, printed wire, or connectors with your hands.-To prevent the hard disk from being affected by static electric
67Step84Insert the hard disk into the hard disk slot.Hold the metal panel portion of the hard disk and insert the disk while aligning it with the guid
68Step811Press [Settings].12Select INITIALIZE MENU using [ ] and [ ], then press [OK].A confirmation message is displayed.13Press [OK].IMPORTANTIf the
6IMPORTANT Do not install the printer in the following locations, as this may result in damage to the printer.-An environment where the temperature a
69Step8IMPORTANT• NB-W2 contains components that are sensitive to static electricity. Observe the following precautions when handling NB-W2 to prevent
70Step8• After removing the protective plate, be careful not to drop screws, paper clips, staples, or other metal objects inside the expansion slot. I
71 Step8 • When you have difficulty communicating, rotate the antenna in the following range to make an adjustment. 7 Connect the power cord. 8 Plug t
FT5-1606 (000) XX2008XXXX ©2008 CANON INC. PRINTED IN JAPANCANON INC.30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, JapanCANON U.S.A., INC.One
7 Installation Space Select an installation location where you can secure the following amounts of free space around the printer, and a surface that
8 Important Safety Instructions Please read these "Important Safety Instructions" thoroughly before operating the printer. As these instruc
Comments to this Manuals