2/3"Hij(s)^E)©a®ToiKi© ©©liiil [Lllli^!^ «OPERATION MANUALz:mm<Dntn^'ii'fz(DiSLm^mm^iim^ < tz ^ I'o ti: L; T ZlJItZ &am
^GENERAL SAFETY INFORMATIONThe safety warnings and cautions provided on the product or in this operation manual must be observed. Fail
AHANDLING THE PRODUCTWARNING1. Never allow water to enter or be spilled on the product. Immediately stop using the product if water enters the product
ADEALING WITH ABNORMALITIES WARNING1. Should any of the abnormalities described below occur, immediately unplug the lens eable from the camera, and t
OTHERAll information contained in this operation manual, as well as the attached or supplemental materials regarding specifications, appearance, and/o
§1. STANDARD COMPOSITION OF THE LENSMake sure all of the following items are included in the packing box.(If you find any item missing, please contact
0 Iris Operation Mode Change-over SwitchUse this switch to change from manual to automatic iris operation and back.(2) Momentary Auto-Iris Switch (Mom
® Connector for Remote Zoom ControlZooming is performed by remote control when this connector is used to connect the unit to an optional control unit
§3. HOW TO MOUNT THE LENS ON THE CAMERA3-1. MOUNTING THE LENS ON THE CAMERA# Before mounting the lens on the camera, make sure that the camera’s power
^ CAUTION: Never hold the lens, lens housing and band portion to support the entire weight of the camera. Excessive force to the mount portion and hou
§4. ADJUSTMENT4-1. FLANGE BACK ADJUSTMENT OF THE LENSAdjust the flange back of the lens as follows:5K (NOTE): Refer to the section 5. OPERATION as for
4. Bring the object into focus by turning the focus ring.5. Set the lens to the wide end by turning the zoom ring.6. Loosen the flange back lock sc
8. Repeat steps 3 to 7 several times until the object is brought into focus at both the wide and telephoto ends.9. After making sure that the object
2. Slide the iris operation mode change-over switch to the “A” position (auto).(also, the camera is required to set an automatic iris mode. Refer to
§5. OPERATION5-1. ZOOM OPERATION(A) MANUAL ZOOM OPERATIONSet the zoom operation change-over knob at the bottom of the lens drive unit to “MANU.” posit
Set the zoom operation change-over knob at the bottom of the lens drive unit to “SERVO” position.For a smooth change, turn the change-over knob while
# Shuttle-Shot FunctionBy simply pressing the ShtI button, you can zoom to a shuttle memory position (preset zoom position) at the maximum speed. When
How to use the shuttle-shot When holding down the ShtI button, the zoom moves toward the shuttle memory position at the maximum speed, and stops at th
DIP switch settingsAt the far end of the rubber cap covering the entire drive unit are the DIP switches which are used for the settings related to the
• Manual operation with the focus ring of the lens:Turn the focus ring clockwise, as viewed from the camera, to focus the lens on a closer object.Turn
S ^ ppENGLISH VERSION...See Page 35
(B) MANUAL IRIS OPERATIONSlide the iris operation mode changeover switch to the “M” position.A\ CAUTION: The iris operation mode change-over switch m
The 2X extender builit in the lens change the focal length of the lens by the factor of 2time. Note that the extender decreases the F number by its ma
When the macro function of the lens is used, macro shooting is enabled.In macro shooting, the object distance becomes shorter than the normal minimum
• Multi-point focus shootingIn macro shooting, when zooming to change the focal length, the focal point varies.The multi-point focus shooting techniqu
5-6. VTR SWITCH AND RET SWITCH OPERATIONS • VTR SwitchPress VTR switch to execute the operation of VTR and press again to stop the operation of VTR.#
§6. PRODUCT SPECIFICATIONS1 X 2 XApplicationFor 2/3" image tube and CCD TV camerasFocal length6.5~78mm 13~156mmZoom ratio12 XMaximum relative ape
r Reference : Lens Designation (For Portable Type Zoom Lens)--A Canon TV zoom lens model name is designated by image size, zoom ratio, focal length at
§7. OPTIONAL ACCESSORIES (SOLD SEPARATELY)To maximize the performance of the lens and provide more flexibility in operation, Canon provides the follow
7-2.SYSTEM CONFIGURATION FOR ZOOM AND FOCUS OPERATIONSSelect the necessary accessories for operating the zoom and focus functions from the following t
Operation combinationsOperation Accessories usedFocusing Remote ManualZoom operation change-over KnobFocusingZoomingRemote ManualRemote ManualMANU (2X
ligi™TECHNICAL DOCUMENTS
g '/Khr_____- TABLE OF THE CONTENTS FOR THE EXCLUSIVE BROCHURE -mmt LTmi itttbx&ijttoThe exclusive brochure consists of a general circuit di
ENGLISH VERSION
------------------------------ FCC REGULATIONS ----------------------------------^ (NOTE) : This equipment has been tested and found to comply with th
— FOREWORD —Thank you for purchasing the Canon TV zoom lens YJ12 x 6.5B.This operation manual consists of the operation manual for the lens and Japane
— CONTENTS —A\ GENERAL SAFETY INFORMATION...........38§1. STANDARD COMPOSITION OF THE LENS.........
Comments to this Manuals