Canon VB-S800D User Manual download pdf (Page 2)

External Dimensions

54 (2.13)

50.0 (1.97)

11.0 (0.43)

53.5 (2.11)

R23 (R0.91)

120 ( 4.72)

Unit : mm (in.)

4.4 ( 0.17)

(mounting screw holes)

54.5 (2.15)

21.0 (0.83)

43.2 (1.70)

9.5 (0.37)

Connecting the Camera

Power Supply

See “Speciﬁcations” > “Others” > “Power Supply”.

Important

• Check with your dealer for more information about PoE devices.

• Some PoE devices allow power limits for each port, but applying

limits may interfere with performance. If using this type of PoE

device, do not limit the operating power.

•

Some PoE devices have total consumption power limits for ports,

which can interfere with performance when multiple ports are in use.

For more information, check the instruction guide for your PoE device.

External Device I/O Terminals



External Device Input Terminals (IN)

The external device input terminal consists of a positive terminal (IN)

and negative terminal (GND). Connecting cables to the positive and

negative terminals and opening or closing the circuit notiﬁes the Viewer.

Important

When connecting sensors and switches, use those that have terminals

which are isolated from internal power and GND.



External Device Output Terminals (OUT)

The external device output terminal consists of an OUT terminal and a GND

terminal. Controls from the viewer can be used to open and close the circuit

between the terminals. A MOSFET device is used for the output terminal.

Rating range for load connected to output terminals.

Rating between output terminals:

Maximum voltage 50 V DC

Continuous load current at or below 100 mA

On resistance: Below 1 Ω

Adaptive wiring for external device cables

Rating Range: (same for contact input and output)

Conductor Size: AWG: No. 26

– 20

Stripped cable length should be approximately 11 – 13 mm (0.43 – 0.51 in.)

Note

• The External Device I/O Terminal consists of three terminals (IN, OUT,

and GND). The GND terminal serves as both the external device

input GND and the external device output GND.

• The GND terminal is connected to the camera interior GND.

•

When using the external device input and output at the same time, couple

the GND wire from the input cable with the GND wire from the output

cable, conforming to the rating range, and connect it to the GND terminal.

•

Do not push the external device I/O terminal button with too much force.

Doing so may cause the button to remain pushed-in.

GND

OUT

GND

Input terminal

Output terminal

1 kΩ

10 kΩ

0.1 µF

10 kΩ

Internal controller

Internal Connection Diagram

Audio Input Terminals

Camera has single audio input system supporting two types of microphone

input: LINE IN and MIC IN. Before use, change [Audio Input] on the Setting

Page (see “Operation Guide”). LINE IN is selected by default.

• Dynamic MIC IN

Input impedence: 20 kΩ

– 40 kΩ

• Condenser MIC IN

Input impedence (microphone bias resistance): 2.2 kΩ ±20%

Microphone power supply: plug-in power (voltage: 2.3 V)

Supported microphones: Condenser microphones with plug-in power support

• LINE IN

Input level: up to 1 Vp-p

* Use a microphone with an ampliﬁer.

Speciﬁcations

Please refer to the installation procedures or “Operation Guide” for

speciﬁcations not listed below.

Camera

Lens 3.5x optical (4x digital zoom) zoom lens with

auto focus

Fixed focal length lens (4x digital

zoom

)

Viewing Angle For 16:9 aspect ratios

Horizontal: 77.7° (W) – 20.7° (T)

Vertical: 40.4° (W) – 11.6° (T)

For 4:3 aspect ratios

Horizontal: 55.3° (W) – 15.5° (T)

Vertical: 40.4° (W) – 11.6° (T)

For 16:9 aspect ratios

Horizontal: 95.0°, Vertical: 60.0°

For 4:3 aspect ratios

Horizontal: 76.0°, Vertical: 60.0°

Pan Angle Range 350° (±175°)

Tilt Angle Range 90º (ceiling-mounted position: -90º – 0º)

When the horizontal direction of the camera is 0°

Rotation Angle Range 180° (±90°)

Interface

Network Terminal*

LAN x 1 (RJ45, 100Base-TX (auto/full-duplex/half-duplex))

* LAN cables are category 5 or higher, with length 100 m

(328 ft.) or shorter.

Audio Input Terminal 3.5 mm ( 0.14 in.) mini-jack connector (monaural)

(common for LINE IN & MIC IN)

LINE IN x 1 or MIC IN x 1

External Device I/O Terminal

Input x 1, Output x 1

Memory Card microSD Memory Card, microSDHC Memory Card,

microSDXC Memory Card compatible.

Others

Operating Environment Temperature: -10°C – +50°C (+14°F – +122°F)

Humidity: 5% – 85% (without condensation)

Storage Environment Temperature: -30°C – +60°C (-22°F – +140°F)

Humidity: 5% – 90% (without condensation)

Installation Angle

±5° (camera) in relation to a horizontal plane

Power Supply

PoE: PoE power supply via LAN cable

(IEEE802.3af compliant)

Power Consumption

Max. 7.8 W

–

Class 0 power sourcing equipment (requests 15.4 W)

Max. 7.6 W

–

Class 0 power sourcing equipment (requests 15.4 W)

Max. 4.1 W

–

Class 2 power sourcing equipment (requests 7.0 W)

Symbols Indicating Safety Precautions

This Installation Guide uses the following marks to indicate important

information the user should know in order to use the product safely.

In this section, explanations are provided for each mark so that

readers will understand the level of importance for each. Be sure to

observe these items.

Warning

Failure to follow the instructions

accompanied by this symbol may result in

death or serious injury.

Caution

Failure to follow the instructions accompanied

by this symbol may result in injury.

Caution

Failure to follow the instructions

accompanied by this symbol may result in

property damage.

Important

This symbol indicates important or

restricted items.

Note

Contains reference information for

operation or additional explanations.

Safety Precautions

Installation Precautions

Warning

Do not install in the following places:

• Places in strong direct sunlight, near heat-generating

objects, or subject to high temperatures

• Places near ﬁre sources or ﬂammable solvents (alcohol,

thinner, fuel, etc.)

• Humid or dusty places

• Places subject to oily smoke or steam

• Places subject to sea air

• Conﬁned or enclosed places

Fire or electric shock may result.

Precautions for the LAN (power) cable:

• Do not set any heavy objects on the LAN cable.

•

Do not pull, forcibly bend, scratch, or modify the LAN cable.

Fire or electric shock may result.

Caution

For installation or inspection of this camera, consult the

dealer where you purchased the product.

• This installation should be made by a qualiﬁed service

person and should conform to all local codes.

• When installing, make sure the surface is capable of

withstanding the total weight of the camera and

accessories, and sufﬁciently reinforce if necessary.

• Be sure to use installation screws designed for the type of

ceiling the camera is to be installed.

• Periodically check the parts and screws for rust and to

see if they have loosened, in order to prevent injuries and

equipment damage due to falling items.

• Do not install in unstable places, places subject to

signiﬁcant vibration or impact, or places subject to salt

damage or corrosive gas.

•

Be sure to attach the safety wire when installing the camera.

Failure to do so may result in the camera falling or other accidents.

• Do not touch the edges of metal parts with bare hands.

• Be careful not to trap your ﬁngers during installation of the

camera.

Injury may result.

Caution

• Do not turn the camera rotator by hand.

•

Do not install on an unstable surface. Also, make

sure the camera is installed ±5°off horizontal.

• After turning off the power, do not turn the power on again

for at least 5 seconds.

• Take measures to remove static electricity before

performing any procedures.

• If there is condensation, please wait to power on, until the

condensation dissipates.

Malfunction may result.

• Take care not to damage wiring or pipes in the room.

Damage to peripheral items may result.

Precautions for Use

Warning

• If you discover defective conditions such as smoke,

strange sounds, heat or strange odors, immediately stop

using the camera and contact your nearest dealer.

Fire or electric shock may result from continued use of the product.

•

If thunder starts, stop installation or inspection etc. and do

not touch the camera or continue connecting the cable.

• Do not disassemble or modify the camera.

• Do not damage the connecting cable.

• Do not spill water or other liquid inside the camera, spray

the camera with water, or otherwise make it wet.

• Do not insert foreign objects into the camera.

• Do not use ﬂammable sprays near the camera.

• Do not leave LAN cables connected when the camera is

not in use for long periods.

• Do not use ﬂammable solvents such as alcohol, paint

thinner or benzine when cleaning the camera.

Fire or electric shock may result.

Only for European Union and EEA (Norway, Iceland and

Liechtenstein)

These symbols indicate that this product is

not to be disposed of with your household

waste, according to the WEEE Directive

(2012/19/EU), the Battery Directive

(2006/66/EC) and/or national legislation

implementing those Directives.

If a chemical symbol is printed beneath the symbol shown

above, in accordance with the Battery Directive, this indicates

that a heavy metal (Hg = Mercury, Cd = Cadmium, Pb = Lead)

is present in this battery or accumulator at a concentration

above an applicable threshold speciﬁed in the Battery

Directive.

This product should be handed over to a designated collection

point, e.g., on an authorized one-for-one basis when you buy

a new similar product or to an authorized collection site for

recycling waste electrical and electronic equipment (EEE) and

batteries and accumulators. Improper handling of this type of

waste could have a possible impact on the environment and

human health due to potentially hazardous substances that are

generally associated with EEE. Your cooperation in the correct

disposal of this product will contribute to the effective usage of

natural resources.

For more information about the recycling of this product, please

contact your local city ofﬁce, waste authority, approved scheme

or your household waste disposal service or visit www.canon-

europe.com/weee, or www.canon-europe.com/battery.

CANON INC.

30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan

CANON EUROPA N.V.

Bovenkerkerweg 59, 1185 XB Amstelveen, The Netherlands

1 2

Comments to this Manuals

No comments

Canon VB-S800D User Manual Page 2

Comments to this Manuals