Canon VB-C50Fi User Manual

NETWORK CAMERAUser’s ManualVB-C50Fi´ENGLISHPlease read this User’s Manual carefully before operation.Be sure to read the “a Safe Use of Equipment” sec

xa Safe Use of EquipmentaAn exclamation point, within a triangle, is intended to alert the user to the presence ofimportant operating and maintenance

4-36Setting Up TimerTo Make Settings...1. With the Schedule Setting Tool, open the Timer Setting Tool.In the Service tab of the Schedule Setting scree

4-37VB Administration ToolsMotion Detection Setting ToolThe section below describes the motion detection function which records pictures, sends data t

4-38t Camera Selection boxFor selecting a camera.y ViewerFor picture display and camera control in the same way as a normal viewer.u Motion detection

4-39VB Administration ToolsFlow of Motion Detection SettingsA summary of the procedures for motion detection is given below. Please refer to each refe

4-40Setting Up Motion DetectionTo Make Settings...1. Open the Motion Detection Setting Tool with the Schedule Setting Tool.In the Service tab in a Nor

4-41VB Administration Toolsq Used AreaCheck the number of the motion detection area to be usedand the detection area frame is displayed in the Viewer.

4-42Tip● If Sensitivity is set at a low level, the device does not recognize the motion evenduring great variations in the image inside the motion det

4-43VB Administration ToolsqwerTip● See “Relationship between ON and OFF events and picture recording” (→ P.4-54)for the ON and OFF event and picture

4-44qwSchedule Setting Tool6. Enter the settings for output to an externaldevice when the device detects motion(Output tab).* The settings in these st

4-45VB Administration ToolsNote● Because the video distribution frame rate may be slowed when the data is sent viaa proxy server, connection without u

xiFCC NOTICENetwork Camera, Model: VB-C50FiN, VB-C50FiPThis device complies with Part 15 of the FCC Rules. Operation is subject to thefollowing two co

4-46TipMotion detection status and screen displayThe area in which the VB-C50Fi is performingmotion detection appears in a blue frame in theViewer.The

4-47VB Administration ToolsqwTipSetting the motion detection level while checking recordedimagesTo set the level of motion detection at motion detecti

4-48q w ertyuNight Mode Setting ToolBelow is a description of the Night Mode function with which you can take pictures in dark conditions.Night Mode S

4-49VB Administration ToolsSetting Up Night ModeTo Make Settings...1. With the Schedule Setting Tool, open the Night Mode Setting Tool.In the Service

4-50rtyui!1o!0!2External Device Input Setting ToolBelow is a description of the External Device Input function which performs video recording whena si

4-51VB Administration Tools!0 Post-event (sec.) and IntervalEnter the required number of seconds, within a range of 0-10 seconds for picture recording

4-52External Device Output Setting ToolThe section below describes the output settings to an external device connected to the Multi-Terminal Module (→

4-53VB Administration ToolsSetting Up External Device OutputTo Make Settings...1. With the Schedule Setting Tool, open the External Device Output Sett

4-54Schedule Setting ToolTipRelationship between ON and OFF events and picture recordingONOFF ONOFFONOFFPicture RecordingAB CDON OFFBelow are methods

4-55VB Administration ToolsTipE-mail Notification Settings dialog boxWhen pictures have been recorded, you can send the recorded picture and data inan

xiia IMPORTANT SAFETY INSTRUCTIONSIn these safety instructions, the word“equipment” refers to the Canon NetworkCamera VB-C50Fi and all its accessories

4-56The Log Viewer is a tool for downloading log files, and viewing and managing the operating statusof the device. The Log Viewer provides monitoring

4-57VB Administration ToolsLog ViewerViewing the LogThe following content is displayed in the log.● CodeThe log displays error codes. For error codes,

4-58Using Selection Criteria to Display LogsLogs can be filtered according to error type, code, or date and time so that only the requiredinformation

4-59VB Administration ToolsAdmin ViewerAdmin Viewer is a viewer which has functions for managing the VB-C50Fi. It has special privilegefunctions that

4-60Starting Up Admin ViewerTo Start Up...1. Click the “Admin Viewer” on the VBAdmin Startup Panel or double-click the“Admin Viewer” icon on the deskt

4-61VB Administration ToolsNoteIf the Admin Viewer window is minimized or in full-screen mode, the notificationmessage for external device input appea

4-62Enabling/Disabling View RestrictionsView restrictions can be enabled or disabled when controlling the camera.1. Choose either “ON” or “OFF” from V

4-63VB Administration ToolsOperating a CameraThe Admin Viewer provides camera control methods not available in the Viewer for PC or Viewerfor Java.Adv

4-64Clicking the Screen to Control the CameraYou can control the zoom operation by clicking and holding the mouse in the viewer to start andreleasing

4-65VB Administration ToolsCamera-Specific FunctionsYou can set up camera-specific features such as settings for exposure, digital zoom and night mode

xiiifig-1EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODEANTENNA LEAD IN WIREANTENNA DISCHARGE UNIT (NEC SECTION 810-20)GROUNDING CONDUCTO

4-66Shade CorrectionIf the background of an image is bright, making the subject difficult to see, you can adjust thecontrast of the darker areas to ma

Creating Web Pages forVideo DistributionThis chapter describes how to use the VB-C50Fi to webcastinformation.Picture data can be distributed in variou

5-2Web Pages for Video DistributionIf you select a link requesting video in step 1, a file that includes the IP address information forthe VB-C50Fi is

Creating Web Pages5-3Web Pages for Video DistributionTipYou can use the Language setting function for the Browser to create a multi-lingualWeb site. F

5-4There are 2 types of viewers: the Viewer for Java and the Viewer for PC.For a detailed explanation of the Viewers, please refer to “Viewer Software

Creating Web Pages5-5Viewer OverviewNoteViewer Software User’s Manual is provided on the CD-ROM supplied with theVB-C50Fi (Viewer-E.pdf).Viewer for PC

5-6This is a LiveApplet sample page which distributeslive videos and allows users to control the camera.This is a sample page which combinesLiveApplet

Creating Web Pages5-7This section describes how to use the Viewers for Java to provide videos. Application examplesare also given.Using the Viewer for

5-8Using the Viewer for Java to Distribute VideosSaving Web Page DataThe VB-C50Fi is equipped with a Flash memory where Web page data can be saved. Da

Creating Web Pages5-9Using the Viewer for Java to Distribute VideosExample of Using the Viewer for Java to Create a Web PageThis section describes an

xiv - Locations exposed to direct sunlight - Locations exposed to salt spray - Close to flammable solvents (alcohol,thinners, etc.)22. When any of the

5-101 sample.htm<html><head><title>SampleSite LiveApplet</title></head><frameset rows="70,*"><frame s

Creating Web Pages5-11Click the button todisplay the page inwhich LiveApplet isembedded.Using Glimpse and LiveApplet TogetherThis section describes ho

5-121 glimps.htm<html><head><script language="JavaScript"><!--function clicked(btn) {url = btn.namewindow.open(url,&quo

Creating Web Pages5-13Providing “LiveApplet” without Camera ControlThis section describes how to create a Web page that only displays live video and h

5-14Certain Images SpecifiedStartup screen Disconnection screenIf no particular image is specified, the “connecting to hostname” (when the hostname pa

Creating Web Pages5-15Displaying the Host Name, Frame Count and Other Information on the Video Screen<param name=show_fps value="on">

5-16Displaying Bitmap Images on the Video Screen<param name=superimpose value="/local/logos/newlogo.gif,0,0">* The underlined portion

Creating Web Pages5-17Viewer for Java ParametersYou can specify applet parameters to provide an applet tailored to modify the behavior orappearance of

5-18Using the Viewer for Java to Distribute VideosWhen a startup screen is specified in the “open_image” parameter, this parameter specifies the displ

Creating Web Pages5-19Using the Viewer for Java to Distribute VideosSpecifies whether or not connection to the camera server should be established sim

xvMaintenanceCleaning the Equipment1. Unplug the AC adapter from the wall outlet.2. Carefully wipe the equipment with a soft cloth that hasbeen moiste

5-20Using the Viewer for Java to Distribute VideosTipWhen specifying an address included in the codebase attribute of the applet tag anda URL paramete

Creating Web Pages5-21This section describes how to use the Viewer for PC to provide videos. Application examples arealso given.If a client is using t

5-22TipInstead of an IP address, you can also type in <_I_P_A_D_D_R_> (→ P.5-9).Example: <_I_P_A_D_D_R_> 65310<_I_P_A_D_D_R_> 65311w

Creating Web Pages5-23Using the Viewer for PC to Distribute VideosInclude the tags that link to the wvh file in the text or images in the Web page.1 &

5-24Distributing Videos Using a Browser OnlyYou can also use the WebView-HTTP protocol to provide videos from the VB-C50Fi directly to a Webbrowser. S

Creating Web Pages5-25GetStillImage ParametersParameter Descriptionz or zoomSpecifies camera zoom. “z” is ten times the zoom ratio of the widest angle

5-26NoteContact respective manufacturers for details on setting the router.One fixed global address is required if the VB-C50Fi is being used to distr

Creating Web Pages5-27You can view still images and control the camera using the Web service of a mobile phone. Youcan easily create still image distr

5-28Example of Creating a Screen for Distribution of a Still Image to a Mobile PhoneOverwriting Sample PagesYou can change screen displays and the con

Creating Web Pages5-29Example of Creating a Screen for Distribution of a Still Image to a Mobile Phonestill.jpg parametersCommand Descriptioncamera_id

xvi

5-30

Using the PictureRecording FunctionThis chapter describes a couple of specific examples of thePicture Recording function using the VB-C50Fi. Still ima

6-2Using the Still Picture Recording Function Linked to an External DeviceBy combining various sensors and switches to operate according to External D

6-3Using the Picture Recording FunctionUsing the Still Picture Recording Function Linked to an External DeviceSample Still Picture Recording SettingsS

6-4Using the Still Picture Recording Function with a Predetermined ScheduleBy using the “Schedule” setting, you can construct a monitoring system that

6-5Using the Picture Recording FunctionUsing the Still Picture Recording Function with a Predetermined ScheduleSample Still Picture Recording Settings

6-6Using the Motion Detection Function with a Predetermined ScheduleBy running the motion detection function according to a schedule, you can construc

6-7Using the Picture Recording FunctionSample Still Picture Recording SettingsSettings specified on the “Camera and Video” page (→ P.3-8)Specify the a

6-8● Next, set the sensitivity, area ratio and duration.To ensure that the event is not triggered by unrelatedlighting changes or small movements, set

6-9Using the Picture Recording FunctionUsing VBCollectorDownloaded image displaysPictures recordedwith the VB-C50Fi’spicture recordingfunctionPictures

Before Using theVB-C50FiThis chapter describes the features of the VB-C50Fi, thehardware and software requirements, and the name andfunctions of the s

6-10Starting Up VBCollectorVBCollector is started up by choosing it from Start menu.To Start Up VBCollector...Choose [Program]-[WebView Livescope]-[VB

6-11Using the Picture Recording Function2. Enter each item in the various fields and clickthe “OK” button.q Server NameAssign a name for recognizing t

6-12TipDownloading images to a shared folder on the network● You cannot specify a path name that uses a network drive in the “Image Directory”setting.

6-13Using the Picture Recording FunctionNoteDownloaded images are not deleted when a server is deleted. To delete downloadedimages, first follow the p

6-14Registering TasksAdding a TaskAdd a new task for downloading images.To Add a New Task...1. To add a task, choose “New Task” from the“Task” menu ba

6-15Using the Picture Recording FunctionNote● Up to 16 tasks can be executed by VBCollector simultaneously. Please be surenot to load a schedule with

6-16Editing TasksThe details of a registered task can be edited.To Edit a Task...1. In the Task View, select the task to be editedby clicking on its n

6-17Using the Picture Recording FunctionDisplay Task StatusDuring the execution of any task, the download status can be checked.To View Task Status...

6-18Starting/Stopping the ServiceThe task scheduler service can be started and stopped.To Make Settings...Choose “Start Service” or “Stop Service” fro

6-19Using the Picture Recording FunctionAutomatic Downloading by NotificationYou will not be able to record images if there is insufficient space on t

1-2The VB-C50Fi is a system that distributes live videos via the Internet or an Intranet. It can be usedin a wide range of applications, such as distr

6-20r “Apply” buttonSaves a change to the reception port number in the registry. If you make a change, a dialogbox is displayed. Click “Yes” and the t

6-21Using the Picture Recording Function3. The Filter dialog box appears. Select thedisplay format and time and click the “OK”button.q Display FormatS

6-224. HTML for displaying the images is generated,the Web browser starts up, and thumbnailimages of the selected date are displayed in100-image units

6-23Using the Picture Recording FunctionAnimate ImagesDownloaded images can be selected using the server name and date to be animated (consecutivedisp

6-24● AnimationImages can be consecutively displayed.[Top] button Shows the original image.[Prev] button Shows the previous image.[Play/Pause] button

6-25Using the Picture Recording FunctionDeleting ImagesDownloaded images can be deleted.To Delete Images...1. Stop the task schedule of the tool.2. Ch

6-26Viewing LogsVBCollector outputs logs concerning the execution of tasks. To view a log, choose “Display Log”from the “Tools” menu bar.The following

6-27Using the Picture Recording FunctionDisplaying Logs According to Selection CriteriaLogs can be filtered according to error type, code, or date and

6-28Search LogsLogs can be searched using character strings. This function is convenient in case of searchingany target log from among numbers of logs

6-29Using the Picture Recording FunctionSelecting Log FilesThe initial log file of VBCollector is saved as “vbrpd.log” file in the “SYSTEM” folder wit

1-3Before Using the VB-C50FiFeatures of the VB-C50FiView Restriction functionYou can set restrictions on camera zoom magnifications. For example, if t

6-30Setting Download CapacityIn order to perform downloads based on a task schedule, you can set the upper limit on thenumber of pictures or specify t

AppendixChapter

7-2TroubleshootingBefore you contact your Canon dealer or service outlet, check the items listed below. If a logmessage is displayed, refer to the log

7-3AppendixTroubleshootingI forgot the password.● All factory defaults settings can be restored by using the Reset switch (→ P.7-21). Thedefault admi

7-4MessageExplanationResponse●A007 View restriction setting error (warning)inconsistent view restriction for camera[1]The view restriction settings ar

7-5AppendixLog MessagesMessageExplanationResponse●A008 Compatibility error in the view restrictions settings (warning)unacceptable view restriction fo

7-6MessageExplanation●A023 Detection in change of point of contact (err)a %1 detected at In%2%1point of contact device input change (front-edge | rear

7-7AppendixLog MessagesMessage●A050 Access permission when restricting user access (info)user %1 access grantedExplanationDuring user access restricti

7-8MessageExplanation●S005 System settings changed (info)System settings updatedThe VB software settings were modified without a reboot. Log MessagesM

7-9AppendixFault SeverityFault which affects task executionFault which does not affect task executionLevelErrorWarningInformation on correct operation

iiIntroductionThank you for purchasing the Canon Network Camera VB-C50Fi (referred to hereafter as the VB-C50Fi).This User’s Manual describes how to s

1-4VB Administration Tools Ver. 2.1 (→ P.4-2)This tool lets you set view restrictions and presets visually and easily. You can also set scheduleswith

7-10Log Messages●S007 (err)Message Execution failure: Invalid server information●S008 (err)Message Download is completed, but failed to get task infor

7-11Appendix●S016 (info)Message Logs generated at the previous task will be merged.Explanation If logs generated while task operation are not output t

7-12Log Messages●D012 (err)Message Failed to get the server information.●D013 (err)Message Cannot create a new directory.●D018 (err)Message Work file

7-13AppendixLog Messages●D029 (err)Message Download was aborted due to insufficient disk space.[%1 remaining, %2required]%1 Disk space currently avail

7-14Log Messages●D038 (warning)Message Downloading of old images is not available. [Images captured before %1]%1 The oldest captured date of a downloa

7-15AppendixVB-C50FiVideo signal Conforms to NTSC/PALImage Sensor 1/4-inch CCDNumber of pixels [NTSC] use: 340,000 (effective 630,000)[PAL] use: 400,0

7-16Specifications+3.3V0.1µF10kΩ 10kΩ10kΩInternal controllerInput terminals IN+, IN–Output terminals OUT A, OUT B+–External Device I/O TerminalsYou ca

7-17AppendixNote● Install the Viewer for PC from the “VBToolsInstall.exe” file on the supplied CD-ROM (→ P.2-11).● The User’s Manual for the viewer so

7-18Sample Network ConfigurationsThis section describes some typical installation modes for the VB-C50Fi.Be sure to assign an IP address to the VB-C50

7-19AppendixUpgrading the Firmware RemotelyNoteDo not turn the power off until you have confirmed that the VB-C50Fi has restarted.Turning the power of

1-5Before Using the VB-C50FiVBCollector Ver. 2.1 (→ P.6-9)This tool is for collecting and viewing still pictures recorded by the VB-C50Fi on a PC.Oper

7-20Restoring the Factory Default SettingsSince the VB-C50Fi supports a wide variety of functions, we recommend that you make a note ofthe settings fo

7-21AppendixRestoring the Factory Default SettingsNote● Do not turn the VB-C50Fi power off while the Restoring operation. If you turn thepower off, al

7-22Factory Default SettingsItem Setting Item Setting 1 Item setting 2 (m) (d) (y) (m) (d) (y)● Administrator ID root● Administrat

7-23AppendixFactory Default SettingsItem Setting Item Setting 1 Item setting 2 (m) (d) (y) (m) (d) (y)● Server(Common Settings)Max

7-24IndexAAC adapter ... iv, 2-6AC cable ...

7-25AppendixIndexInstall ... 2-11Interlace Mode ...

7-26IndexSave Setting button ... 3-4Schedule name ...

CANON INC. 30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, JapanU.S.A. CANON U.S.A.,INC. NEW JERSEY OFFICE100 Jamesburg Road, Jamesburg, NJ 08831

1-6If you finish setting the VB Initial Setup Tool (initial settings) or wish to stop the AutomaticDownload by Notification function using VBCollector

1-7Before Using the VB-C50FiViewer Software for Monitoring Use (Sold separately)If WebView Livescope MV Ver. 2.1 is used, up to 16 viewer screens can

1-8System Components and Their OperationFrontLAN status LEDThe LED blinks during communication.100Base-TX ... Green10Base-T ...

1-9Before Using the VB-C50FiMAC addressThe MAC address is requiredwhen setting the IP addressand making other networksettings. Please make anote of it

1-10Using the Multi-Terminal Module (VB-EX50), you can connect external devices such as differentkinds of sensors to the unit, and store images by sen

Setting UpThis chapter explains how to set up the VB-C50Fi, run initialchecks, and confirm that the camera’s images are displayedcorrectly.Chapter

2-2Set up the camera1Perform initial settings for the camera3Connect the camera to the network2LAN cableVB-C50FiHubSet up the device.Make sure the dev

2-3Setting UpSetup WorkflowInstall the software5Check operation of the camera4Access the device with your PC, then display to check the image from the

iiiRequest concerning disclosure of live videosWith respect to the disclosure of live videos, we request that sufficient consideration begiven to matt

2-41. Set Up the Cameraa WARNING:Install the camera securely.● When installing the VB-C50Fi on the ceiling or a wall, contact your Canon dealer.● When

2-5Setting Up1. Set Up the Camera-Note● The camera may not operate correctly if a wide converter other than the WL-37is used.● Be sure to install the

2-6Turning the Power ON and OFFThe VB-C50Fi itself does not have a power switch. You can switch the VB-C50Fi on by pluggingthe AC adapter into a wall

2-7Setting UpOnce your PC and the camera are connected, perform the initial settings next. The instructionshere follow on from “2. Connect the Camera

2-83. The camera connected to the networkis automatically detected and its MACaddress, IP address and model nameare displayed.The factory default sett

2-9Setting Up5. A setup progress window appears andyour settings will be saved.Note● Set the IP address to a value that suits your environment.● Where

2-102. Your Web browser starts up and thetop page of the camera server appears.Click the “Using Viewer for Java” or the“Using Viewer for PC” and check

2-11Setting Up5. Install the SoftwareYou must install software to display images from the camera and to manage the camera. Thereare 3 types of softwar

2-12Viewer Software OverviewBy using the Viewer software, you can view images sent from the VB-C50Fi on a PC, as well ascontrol the camera. Below is a

Basic SettingsThis chapter describes the basic settings for the VB-C50Fisuch as network connection, camera control, date and timesetting and mail. Be

ivPackage ContentsThe VB-C50Fi package contains the following items. If any of these items is missing, pleasecontact the retailer from which you purch

3-2What Can I Do on Each of the Settings Pages?Proceed to each of the settings pages from the Settings Title Page where you can perform varioussetting

3-3Basic SettingsAccessing the Settings Title PageNoteThis manual uses the IP address 192.168.100.1 (the factory default setting) below asan example t

3-4Settings Title PageFrom the Settings Title Page, you can move to each settings page, confirm the settings afterchanging, and save the changes to th

3-5Basic SettingsYou can perform the following settings with System and Network.● Root Account: For setting up passwords.● Ethernet: For setting up IP

3-6Ethernet12Note● Contact the network administrator for the IP address, subnet mask and defaultgateway address settings.●Take particular care with th

3-7Basic SettingsConnection Keeping123Setting Up the Administrator Password and Ethernet etc. (System and Network)1 “Send packet regularly”Check to en

3-8You can perform the following settings with Camera and Video.● Video Capture: For setting image size and quality.● Camera Control: For setting the

3-9Basic SettingsCamera Control1234Setting Camera Control, Image Size and Quality (Camera and Video)53 “Interlace Mode”Select either “Weave (Interlace

3-10Setting Camera Control, Image Size and Quality (Camera and Video)Camera Names1 “Camera Name”Used in the camera selection box on the viewers (→ P.1

3-11Basic SettingsPresetting Best Shot (Preset)You can perform the following settings with Preset.● Common Settings: For setting the tour schedule of

vContentsIntroduction ... iiPackage Contents ...

3-12Tip● Even if you have set Auto Preset Tour to “For Viewers” or “Always”, the Preset Tourwill not work while you are controlling the camera with th

3-13Basic SettingsTipYou can make preset settings more easily with the VB Administration Tools. Pleaseuse the VB Administration Tools for the settings

3-14You can perform the following Settings with Server.● Common Settings: For setting up the environment where users can connect to theVB-C50Fi.● HTTP

3-15Basic SettingsHTTP Server12Setting Up the HTTP and Camera Servers (Server)1 “HTTP Port”Sets the TCP port number for the HTTP. Enter a value betwee

3-16Camera Server1234567Setting Up the HTTP and Camera Servers (Server)1 “Video Transmission Port”Sets the TCP port number for the video transmission

3-17Basic SettingsSetting User Access Privileges (Access Control)You can perform the following settings with Access Control.●Authorized User Account:

3-18Authorized/Restricted Host SpecificationNote● If you do not make a Host List, access is permitted to any hosts.● If the Host List provided prohibi

3-19Basic SettingsTipThe Host Restriction function applies to hosts running client applications such asviewer. Access restrictions are imposed using a

3-20Setting the Date and Time (Date and Time)You can perform the following settings with Date and Time.● Current Camera Time: Displays the time set up

3-21Basic SettingsNew Camera Time123Time Zone1TipEven if you have selected “Synchronize with NTP server”, the data and time will notchange if the VB-C

viContentsPresetting Best Shot (Preset) ... 3-11Setting Up the HTTP and Camera Server

3-22You can perform the following settings with Miscellaneous.● DNS: Register the Name Server Address and Host Name for registering host namessuch as

3-23Basic SettingsMail135246Setting Up Name Server Address and Mail etc. (Miscellaneous)1 “Mail Server Host”Specifies the SMTP server.2 “Sender’s (Fro

3-24External Device Names12LED1Setting Up Name Server Address and Mail etc. (Miscellaneous)1 “External Input Device 1-2”“Device Name”To distinguish be

3-25Basic SettingsYou can perform the following settings with the Administration Tools.● On-board File System Information: Displays the status of VB-C

3-26Miscellaneous1 “View Log Events”Click the “View” button to see the historical log files of the VB-C50Fi’s operation, such asconnection with viewer

VB Administration ToolsChapter 4 describes practical ways of operating the VB-C50Fi using the VB Administration Tools to set viewrestrictions, set pre

4-2Overview of VB Administration ToolsVB Administration Tools comprises “VBAdmin Startup Panel”, “View Restriction Tool”, “PresetSetting Tool”, “Sched

4-3VB Administration ToolsVBAdmin Startup Panel (→ P.4-5)This is the main panel of VB Administration Tools. The tools arestarted up from this panel.In

4-4Overview of VB Administration ToolsLog Viewer (→ P.4-56)This tool enables viewing of operation status logs that are outputto the VB-C50Fi.Admin Vie

4-5VB Administration ToolsStarting Up VB Administration ToolsTo Start Up...1. Double-click the “VB Admin Tools” desktopicon or select “VB Admin Tools”

viiContentsEnabling/Disabling View Restrictions ... 4-62Operating a Camera ...

4-63. The VBAdmin Startup Panel starts up.The five tools---“View Restriction Tool”, “Preset SettingTool”, “Schedule Setting Tool”, “Log Viewer” and“Ad

4-7VB Administration ToolsThe View Restriction Setting Tool is a tool that allows you to set the zoom range easily with themouse.The View Restriction

4-8View Restriction Tool Display ScreenAn overview of the functions of the GUI displayed when the View Restriction Tool starts up isshown below.qertyu

4-9VB Administration ToolsView Restriction Toolt Camera Selection boxSelect the camera to be used to apply view restriction settings.y “Apply the view

4-10Setting View RestrictionsYou can set up a view restriction by either entering a value in the view restriction setting input boxor by using the fol

4-11VB Administration ToolsView Restriction ToolRetrieving Values from the Camera Zoom Position of the AdminViewer and Changing SettingsAdmin Viewer c

4-12NoteAfter the view restrictions have been set, please check to be sure the viewer is correctlyreflecting the view restrictions. When checking from

4-13VB Administration ToolsPreset Setting ToolThe Preset Setting Tool enables you more visually and easily to set Presets and home position.Presets ar

4-14Preset Setting ToolPreset Setting Tool Display ScreenThe display screen for the Preset Setting Tool is divided into the “Preset Settings Area” and

4-15VB Administration ToolsPreset Setting Toolt Preset Selection boxSelect the preset to set or “Home”. “Home” is the setting for home position.y “For

viiiContentsRegistering Tasks ... 6-14Executing and Ca

4-16Preset Setting ToolSetting PresetsYou can set up Presets by either entering a value in the camera parameters or by using thefollowing 2 methods. S

4-17VB Administration ToolsRetrieving Values from the Camera Zoom Position of the AdminViewer and Changing SettingsStart up Admin Viewer and set the c

4-18Tip● You can set a maximum of 10 presets.● Changes in the preset settings are not reflected to the viewer while it is connected.● After the preset

4-19VB Administration ToolsPreset TourA Preset Tour can tour and monitor two or more specified Presets.You can also set Preset Tour with “Presetting B

4-20TipPreset Tour does not operate when the camera is being controlled with the Viewerfor PC, or the Admin Viewer and so on.Preset Setting Toolo Spee

4-21VB Administration Tools2. Select the preset number you want to add tothe Tour Schedule from the Preset settingarea and click the “Add” button.The

4-22Schedule Setting ToolWith the Schedule Setting Tool, you can set up Timer, Motion Detection, Night Mode, ExternalDevice Input and External Device

4-23VB Administration ToolsSchedule Setting Tool Display Screen (Toolbar)There are two kinds of Schedule settings, Normal Schedule and Special Schedul

4-24Normal ScheduleWith Normal Schedule, you can set up a schedule of one week from Sunday to Saturday. Forexample, during the weekend when there is n

4-25VB Administration ToolsSetting Up a Normal ScheduleTo Make Settings...1. With the Normal Schedule displayed, selectan optional schedule number.The

ixHow to Read This ManualNETWORK CAMERAUser’s ManualPlease read this instruction manual carefully before operation.Be sure to read the “a Safe Use of

4-26Schedule Setting ToolTip● On Weekly setting, if you specify the same time and the same day in start and endtime, end time will be the same time in

4-27VB Administration ToolsTip● You can register different settings for each setting number. The number of settingnumbers that can be registered diffe

4-28Special ScheduleWith Special Schedule, you can set up a schedule on one specific day of the week. For example,on a public holiday when there is no

4-29VB Administration ToolsTip● You can only set one type of Special Day per day.● You can set one Special Day a maximum of 32 times.● You can also se

4-303. Double-click the sub-schedule track.The Special Schedule Settings dialog box appears.Enter settings for the schedule.4. Enter the name of the S

4-31VB Administration Tools6. Display the Service tab and enter settings for the services.For more information about the services you can set, please

4-32Tip● An icon for the service you have set up appears in the schedule track in the calendar.However, where the schedule track is short, it may be t

4-33VB Administration ToolsResetting Schedule SettingsResets schedules you have set.1. In the Normal or Special Schedule Setting screen, select “Initi

4-34Setting Up ServiceSet up the services to be performed in the schedules.To open the settings screen for each service, in the“Service” tab in the Sc

4-35VB Administration ToolsTimer Setting ToolThe section below describes the “picture recording” function which takes still images at specifiedtimes a