Canon VB101 User Manual Page 47
- Page / 59
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Troubleshooting
6
92 93
Classification
crit
err
Fault Severity
Critical fault at the software level (stops task operation)
Fault involving a malfunction (operation interrupted)
Level
Error
Error
warning
notice
info
Fault not involving malfunction
Fault outside the system
Information on correct operation
Warning
Warning
Information
Message
Explanation
Response
●A002 Protocol initialization failure (err)
%1 protocol not installed
Webview or VIEW-Windows initialization failed.
The settings may be corrupted.
Correct the settings or restore the factory default settings.
%1
protocol type <LS/C|LS/D|LS/H|VW/C|VW/D|VW/E>
Message
Explanation
Response
●A004 Fault in initial video input systems settings (warning)
initial video input %1 marked inactive
Because there was no input for the initial video input system,
VB101 has switched to automatic detection mode. The settings may be corrupted.
Correct the settings or restore the factory default settings.
%1
Camera number (1-4)
Message
Explanation
Response
●A005 Camera control channel assignment error (warning)
conflicting channel assignment for %1
The same camera control port is assigned to multiple video input channels.
The settings may be corrupted.
Correct the settings or restore the factory default settings.
%1
Camera control port (CC1|CC2)
Message
Explanation
Response
●A006 Camera control system initialization failure (err)
cannot open camera control port %1
The camera control port cannot be opened.
If rebooting does not recover this problem, there is a malfunction. Contact an authorized Canon service representative.
%1
Camera control port (CC1|CC2)
Message
Explanation
Response
●A007 View restriction setting error (warning)
inconsistent view restriction for camera[%1]
The view restrictions settings are corrupted.
The camera control functions on the affected camera cannot be used.
Restore the factory default settings or reset the permitted field of view restrictions.
%1
Camera number (1-4)
Message
Explanation
Response
●A008 Compatibility error in the view restrictions settings (warning)
unacceptable view restriction for camera[%1]
Even in the telephoto field of view, the view restriction settings cannot be satisfied in the horizontal or vertical direction. When this occurs,
the zoom setting is fixed at the telephoto field of view, and camera head control is prohibited in directions that do not satisfy the permitted field of view restrictions.
Set appropriate values for the permitted field of view restrictions.
%1
Camera number (1-4)
Message
Explanation
●A010 Camera control driver start and stop (info)
%1 driver for camera[%2] %3
The camera control device was detected and the driver started up,
or a camera control device error was detected and the driver stopped.
%1
Camera type (Canon VC-C1|Canon VC-C3|Canon VC-C4|Canon VC-C4R)
%2
Camera number (1-4)
%3
started|stopped
Message
Explanation
●A011 Camera control device error (warning)
%1[%2] malfunction (%3)
Camera control device I/O error.
%1
Camera type (VC-C1|VC-C3|VC-C4)
%2
Camera number (1-4)
%3
Error (read|write|timeout|...)
Response
If this occurs frequently, this is a malfunction. Contact an authorized Canon service representative.
Message
Explanation
●A014 Access prohibited due to host restriction (notice)
%1@%2 access denied
Access to the client was denied due to host restrictions . (LS indicates a WebView client,
VW indicates a VIEW-Windows client. Normally, the same message is displayed several times.)
%1
Client type (LS|VW)
%2
Client host IP address
Log Messages
Log Messages for Applications
The Syslog log messages are classified into the following 5 categories. Classification details are dealt with
in the UNIX syslog and the levels are explained in Chapter 3 (→P.54).
Log Messages
* The syslog facility is local7.
- User's Manual 1
- Introduction 2
- Safe Use of Equipment 3
- Contents 5
- Before Using the VB101 6
- Features of the VB101 7
- System Configuration 8
- Java Viewer version 3.10 9
- Helper Viewer version 3.10 9
- Rear View 10
- Front View 10
- Chapter 11
- Installation 11
- Package Contents 12
- Precautions for use 12
- Using a PCMCIA Card 13
- Connecting the Components 13
- LAN plus Dialup Environment 14
- Setup Procedures 15
- Sample page 17
- Detail Settings 18
- System Settings Page 19
- Basic Settings Page 19
- Network Settings Page 20
- VC-C4 VC-C4R 22
- VC-C3 VC-C1 22
- Preset Settings Page 23
- Access Control Settings Page 25
- Listing Guidelines 26
- Listing Format 26
- Application Settings Page 27
- Miscellaneous Settings Page 28
- Creating Web Pages 29
- Internet 30
- Features of the Helper Viewer 31
- Viewing Sample Pages 32
- The text displayed in a 33
- Frame with the embedded 33
- Java Viewer 33
- Frame settings 33
- Nothing Selected 35
- Certain Images Selected 35
- Sample transparent GIF 36
- Java Viewer Parameters 37
- Setting Up the Web Server 38
- Creating wvh files 38
- Frames As a Movie at Access 39
- Using the Picture 40
- Recording Function 40
- Sensors mounted on the door 41
- Connector Attached Cable 42
- Viewing Recorded Pictures 43
- Pictures Search CGI 44
- Troubleshooting 45
- Log Messages 47
- Appendix 52
- Specifications 53
- ■Internal Connection Chart 53
- Using the Enclosed Software 54
- Factory Default Setting 56
- <V> 58
- <W> 58
- <Z> 58
Related products and manuals for Security cameras Canon VB101
Security cameras Canon VB-M40B User Manual
(149 pages)
(149 pages)
Security cameras Canon CA-30 User's Guide
(151 pages)
(151 pages)
Security cameras Canon PowerShot G1 User's Guide
(144 pages)
(144 pages)
Security cameras Canon VB-M700F User Manual
(152 pages)
(152 pages)
Security cameras Canon DS-8 Instruction Manual
(172 pages)
(172 pages)
Security cameras Canon EOS 10D User Manual
(184 pages)
(184 pages)
© 2020, manymanuals.com. All rights reserved. | 0.610 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals