10
Switches 1 & 2 control the address code of the UndercoverEye™ Trekker LANC controller box.
Both the SlimFire Remote Control or Wireless PIR Sensor, and UndercoverEye™ Trekker LANC
controller box need to be set to the same address code in order for the unit to function properly.
There are 4 unique address codes you can set the UndercoverEye™ Trekker LANC to respond
to.
The UndercoverEye™ Trekker LANC is compatible with the SlimFire remote and PIR wireless
motion sensors. The address code here is the “house code” from A-P, however, the
UndercoverEye™ Trekker LANC only will recognize “house codes” A-G. For more information
about setting the house code on your SlimFire remote or Wireless PIR Motion Sensor.
Out of the box both the SlimFire remote, Wireless PIR sensor, and Remote VideoEye™ will
be defaulted to the “A” Address Code.
Why set different address codes? There may be a situation when you want to have several
UndercoverEye™ Trekker LANC units in a recording session. You may want to only have several
UndercoverEye ™ units respond to SlimFire or Wireless PIR motion sensors. For this you have
the ability to set the address between each of these devices. It is a good idea to use a marking
pen and write the address code on your SlimFire remote or Wireless PIR motion sensor if not set
in the default “A” address code.
Camcorder Mode
Switch 3 is the setting the mode to operate the camcorder. The default setting, switch 3 down, is
VTR mode. In this mode the camcorder will act as a tape deck and you will need to connect a
video camera to the camcorder video input such as the supplied bullet camera. When in this
mode the camcorder will record the incoming video signal from the bullet camera. Note, in this
mode you may have to set your camera into VTR mode. Camcorders such as the Sony HC-40 do
not have a VTR switch and the UndercoverEye™ Trekker LANC will automatically put the
camcorder into VTR mode.
By setting switch 3 up you are recording from the camcorders built in camera. The bullet video
camera will not be used in this mode; however, you can connect an IR array for a night covert
setup. When using an IR array be sure to put your Sony camcorder in NightShot mode. You will
also have to build a small waterproof housing for the camcorder for outdoor setups in this mode.
Wireless PIR Sensor or KeyFob Mode
Switch 4 is the setting to let the UndercoverEye™ Trekker LANC know if you are using the
KeyFob or PIR sensor.
In the Wireless PIR sensor mode, DIP switch 3 in the DOWN position the Trekker LANC will
respond wireless PIR sensors. Note, the unit will still respond to the KeyFob by pressing the “on”
button on the KeyFob unit, however, it will not respond to the KeyFob “off” button. If using the
KeyFob in this mode the recording time is setup by switches 4, 5, and 6.
In the KeyFob mode, DIP switch 3 in the UP position the Trekker LANC will respond to the “on”
button from the KeyFob to turn the Trekker LANC on into recording mode, and by pressing the
“off” button on the KeyFob will power down the Trekker LANC. Note, you can still trigger the unit
via the wireless PIR sensor but the unit will power down when the “off” command is sent by the
wireless PIR sensor. In default mode this is one minute after a PIR trigger, but this time can be
adjusted manually in the PIR sensor. Please see the paper instructions inside the PIR sensor for
more information.
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals