Canon DR-6030C User Manual

Document ScannerUser’s GuidePlease read this manual before using this unit. After you finishreading this manual, keep it in a safe place for future re

4 ContentsChapter 3 Software Setup ... 631. ISIS/TWAIN Driver Properties Dialog Box ...

94 Software SetupWith the TWAIN driver, load a document in the scanner and click the [Preview] button to scan one page. The scanned image is displayed

Software Setup 95Chapter 3The [Setting] button allows setting a delay time from when a document is loaded until scanning starts.Set a delay time when

96 Software SetupImage Adjustments for Scanning• To enhance text in documents with a background (when scanning in black and white (binary) mode.)Selec

Software Setup 97Chapter 3• To rotate images to match document textSelect [Text Orientation Recognition] on the [Image processing] tab sheet. The text

98 Software Setup• To skip or enhance a custom colorSelect [Drop-out color Custom] or [Custom color Enhance] in the [Color drop-out] list on the [Imag

Software Setup 99Chapter 3Prescan• To confirm images before scanningSelect the [Prescan] check box on the [Others] tab sheet, and scan. When scanning

100 Software Setup

Chapter 4Appendices1. Regular Maintenance ... 102Cleaning the Scanner ... 102Cleaning the feed path ...

102 Appendices1. Regular MaintenanceClean the scanner on a regular basis as described below to maintain peak scanning quality.CAUTION• When cleaning t

Appendices 103Chapter 4Cleaning the Sensor Glass, Shading Boards, and the RollersIf scanned images have extraneous marks, or if the scanned documents

Chapter 1Before Using the Scanner1. Important Safety Instructions ... 6Installation Location ... 6Power .

104 Appendices3. Use a clean dry cloth to wipe dirt off the sensor glass. Wipe both the top and bottom sensor glasses.IMPORTANTScratches on the sensor

Appendices 105Chapter 46. Wipe the removed rollers with a firmly wrung cloth moistened with water.IMPORTANTDo not use detergent to clean the rollers,

106 AppendicesCleaning the Shading BoardsThe shading boards are the white standard boards located behind the platen rollers. A dirty shading board may

Appendices 107Chapter 45. Press the stop button.The shading board goes back in.6. Close the upper unit slowly. Be sure that the upper unit is complete

108 Appendices2. Removing and Attaching the RollersFollow the relevant procedure to remove and attach the pickup roller, feed rollers and retard rolle

Appendices 109Chapter 4Resetting the CounterAfter replacing the feed rollers, open the [Counter setup] dialog box and reset the counter.1. Follow the

110 Appendices Windows XPSwitch the Control Panel to Classic View, or select [Printers and Other Hardware] in the working field. Windows VistaSwitch

Appendices 111Chapter 43. Click [View devices and printers]. (For Windows XP and Windows Vista, click [Scanners and Cameras].)4. Select [CANON DR-6030

112 Appendices[CANON DR-6030C USB Properties] (or [CANON DR-6030C SCSI Properties]) is displayed.2. Click the [Maintenance] tab.

Appendices 113Chapter 43. Click the [Reset] button, and then make sure that the counter for the roller being used is set to 0.Removing and Attaching t

6 Before Using the Scanner1. Important Safety InstructionsTo ensure the safe operation of this scanner, be sure to read the safety warnings and precau

114 AppendicesRemoving the Pickup Roller1. Turn ON the power.NoteBecause the pickup roller locks when the power is OFF, it will not fall forward when

Appendices 115Chapter 4Attaching the Pickup Roller1. Hold the new pickup roller (or the one you removed) by both sides of its shaft, and place it on t

116 Appendices4. Close the upper unit slowly. Be sure that the upper unit is completely closed by pushing on both edges with both hands until you hear

Appendices 117Chapter 42. Remove the roller cover.3. Move the roller lock lever down and forward (➀), and then slide it to the right (➁).4. Shift the

118 AppendicesAttaching the Feed Roller1. Position the feed roller so the notch in the roller is facing the scanner’s shaft.2. Slide the roller lock l

Appendices 119Chapter 45. Close the upper unit slowly. Be sure that the upper unit is completely closed by pushing on both edges with both hands until

120 Appendices2. Remove the roller cover.3. Move the roller lock lever upward (➀), and then slide it to the right (➁).4. Shift the retard roller to th

Appendices 121Chapter 4Attaching the Retard Roller1. Position the retard roller so the notch in the roller is facing the scanner’s shaft.2. Slide the

122 Appendices4. Attach the roller cover in order of ➀ Æ ➁.5. Close the upper unit slowly. Be sure that the upper unit is completely closed by pushing

Appendices 123Chapter 43. TroubleshootingThis section describes the possible problems that might occur during use of the scanner and how to solve them

Before Using the Scanner 7Chapter 1The following conditions are recommended for optimal scanning quality:Room temperature: 10 °C to 32.5 °C (50 °F to

124 AppendicesProblem The scanner does not support your USB interface.Solution This product is not guaranteed to operate with all types of USB interfa

Appendices 125Chapter 4Windows 7Click [Start] - [Control Panel] - [Hardware and Sound] - [Device Manager], and make sure that no “x” or “!” symbol app

126 AppendicesScanning Is Not PerformedCheck the following if the scanner does not scan an image even though the scanning operation is performed:• Has

Appendices 127Chapter 4Problem The USB cable does not support Hi-Speed USB 2.0.Solution Use the USB cable provided with the scanner.Problem The USB hu

128 AppendicesSaved Image Files Do Not OpenWhen image files saved by CapturePerfect 3.0 cannot be opened by other applications, the probable causes ar

Appendices 129Chapter 4Scanning Results Are Not as ExpectedIf there is a problem with the scanning result (e.g., the scanned image is not clear, or th

130 AppendicesSymptomsLines, smudges, or dirt appear on the scanned image.Problem The scanning glass or rollers inside the scanner are dirty.Solution

Appendices 131Chapter 44. Uninstalling SoftwareIf the ISIS/TWAIN driver, and “CapturePerfect 3.0” are not operating normally, follow the procedure bel

132 AppendicesThe [Uninstall or change a program] window appears.NoteFor Windows XP, the [Add or Remove Programs] dialog box appears.3. From the list

Appendices 133Chapter 44. The file delete confirmation screen appears. Click the [Yes] button.Uninstallation starts.5. After uninstallation is complet

8 Before Using the ScannerHandlingWARNINGNote the following precautions whenever using the scanner. Failure to do so may result in a fire or electric

134 Appendices5. SpecificationsSpecificationsType Desktop sheetfed scannerScanning Document SpecificationsWidth:Length:2.08" to 11.8" (53 to

Appendices 135Chapter 4• The functions described above can be used if they are supported by the application software.• Some functions may not be avail

136 AppendicesOptionsReplacement parts• Refer to “Removing and Attaching the Pickup Roller,” on p. 113 for information about replacing the rollers.• C

Appendices 137Chapter 4External Dimensions26.3" (668 mm)(Document Feed Tray Extension is open)15.6" (398.4 mm)7.6" (194 mm)21.3" (

138 IndexIndexCCapturePerfect 3.0 ...32Operation guide ...17Starting CapturePerfe

PUB. CE-IE-824 © CANON ELECTRONICS INC. 2010CANON ELECTRONICS INC.1248, SHIMOKAGEMORI, CHICHIBU-SHI, SAITAMA 369-1892, JAPANCANON U.S.A. INC.ONE CANON

Before Using the Scanner 9Chapter 1• Do not block ventilation openings. Doing so could case the scanner to overheat, creating a risk of fire.• Never p

10 Before Using the Scanner2. Features of the DR-6030C Document ScannerThe main features of the DR-6030C document scanner are described below. Fast D

Before Using the Scanner 11Chapter 1 DeskewThe scanner straightens an image after detecting an image on a document that was loaded askew. (See “[Desk

12 Before Using the Scanner Remove Binder HolesDeletes black spots left when scanning documents that have had holes punched in them to be stored in a

Before Using the Scanner 13Chapter 13. Names and Functions of PartsThis section describes the name and function of each part. Make sure to read this s

Document Scanner DR-6030CEasy Start GuideThis manual describes the procedures for setting up the scanner for use. For details on how to use the scanne

14 Before Using the Scanner RearCAUTIONDo not block the ventilation openings. Doing so could cause the scanner to overheat, creating a risk of fire.

Before Using the Scanner 15Chapter 14. Installation RequirementsTo use the DR-6030C, your computer must satisfy the following system requirements.• On

16 Before Using the Scanner- Not all USB interfaces provided as standard with personal computers are guaranteed. Contact your local authorized Canon d

Before Using the Scanner 17Chapter 15. About the Setup DiscThe Canon DR-6030C scanner setup disc contains the software listed below:• DR-6030C DriverS

18 Before Using the Scanner

Chapter 2Using the Scanner1. Documents ... 202. Preparing the Trays ... 22Setting Up t

20 Using the Scanner1. DocumentsThis scanner can scan documents ranging in size from business cards and checks to A3 size documents. It can also scan

Using the Scanner 21Chapter 2• Scanning documents that are written in pencil or similar material can make the rollers dirty, which can then transfer t

22 Using the Scanner2. Preparing the TraysPrepare the document feed tray and document eject tray according to the paper size and feed/eject method.Set

Using the Scanner 23Chapter 2Document Eject TrayThe scanner has two eject methods; documents can be ejected to the front of the scanner in a U-turn pa

Connecting the Scanner to Your PCConnect the scanner with the following 1 to 5 procedures. The scanner can be connected to a computer in two ways. Sel

24 Using the Scanner2. Pull the document eject tray extension towards you to open it.IMPORTANTMake sure the document eject tray extension is open when

Using the Scanner 25Chapter 2Installing the Document Eject GuideWhen scanning a document that is particularly thin or particularly long, it could droo

26 Using the Scanner4. To remove the document eject guide, lift the document eject tray extension a little and unhook the document eject guide.5. Reve

Using the Scanner 27Chapter 23. Placing DocumentsThere are two methods for paper separation, called the page separation mode and bypass mode for feedi

28 Using the Scanner2. Straighten the edges of the stack of documents to be scanned.CAUTION• Do not place the documents on top of the scanner to align

Using the Scanner 29Chapter 2IMPORTANTThere is a load limit mark ( ) on the document guides. Do not stack documents higher than this mark (approximate

30 Using the ScannerHow to Feed with the Bypass Mode1.Move the feed selection lever on the lower left side of the front of the scanner down ( ).Note•

Using the Scanner 31Chapter 24. One sheet of the document is pushed against the document feed slot. The document is fed.IMPORTANT• When scanning docum

32 Using the Scanner4. Scanning DocumentsWhen it scans with the DR-6030C, you need to install CapturePerfect 3.0, which is provided with the scanner,

Using the Scanner 33Chapter 2• Scan JobThe scanning conditions and scan mode (Scan Batch to File, Scan Batch to Print, or Scan Batch to Mail) are regi

iFCC REGULATIONS (For 120 V model)Document Scanner, Model M111061This device complies with Part 15 of the FCC Rules. Operation is subject to the follo

34 Using the ScannerCapturePerfect 3.0 Operation ProcedureThis section describes how to start up CapturePerfect 3.0, select the scanner, and the proce

Using the Scanner 35Chapter 2CapturePerfect 3.0 starts up.2. Follow the procedure below to select the Canon DR-6030C document scanner as the scanner t

36 Using the ScannerNoteIf [CANON DR-6030C] is not displayed in the list of scanners, re-install the ISIS/TWAIN driver. (See “Step 3. Installing the S

Using the Scanner 37Chapter 2ISIS Driver basic setup dialog box opens.4. Set the scan settings.For details setting the scanning settings, see “ISIS/TW

38 Using the Scanner6. On the [Scan] menu, select [Scan Batch to File]. The [Scan Batch to File Setting] dialog box opens.For more details on how to s

Using the Scanner 39Chapter 28. When there are no more pages of the document to scan, scanning stops. Scanning resumes or ends according to the “Feedi

40 Using the ScannerStarting CapturePerfect 3.0 with the Start ButtonDR-6030C and Captureperfect 3.0 support Windows’ event functions. After installin

Using the Scanner 41Chapter 2 Windows XPSwitch the Control Panel to Classic View, or select [Printers and Other Hardware] in the working field. Wind

42 Using the Scanner3. Click [View devices and printers]. (For Windows XP and Windows Vista, click [Scanners and Cameras].)4. Select [CANON DR-6030C]

Using the Scanner 43Chapter 2[CANON DR-6030C USB Properties] (or [CANON DR-6030C SCSI Properties]) is displayed. 5. Click the [Events] tab.

iiREAD CAREFULLY BEFORE OPENING THE SEALED DISK PACKAGECANON SOFTWARE LICENSE AGREEMENTIMPORTANT-READ THIS AGREEMENT BEFORE OPENING THE SEALED DISK PA

44 Using the Scanner2. In the initial status, all the applications displaying [Send to this application] are checked. Select one application to be sta

Using the Scanner 45Chapter 2Before using Adobe Acrobat 9.0There are two methods for scanning a document from the scanner using the bundled Adobe Acro

46 Using the Scanner3. In the [User Interface], select [Show Scanner’s Native Interface] and then click [OK] to close the dialog box.4. When you click

Using the Scanner 47Chapter 25. Using Patchcode SheetsThe DR-6030C ISIS driver and CapturePerfect 3.0 both support the automatic file separation funct

48 Using the ScannerAbout Patchcode SheetsPatchcode sheets are data in a portable document format (PDF). There four types; [PATCH II (A4)], [PATCH II

Using the Scanner 49Chapter 2Patchcode Pattern FunctionThere are two types of patchcodes and their function changes according to their pattern. PATCH

50 Using the ScannerIMPORTANTNote the following points when copying a patchcode pattern to create a different size patchcode sheet.• When copying a pa

Using the Scanner 51Chapter 26. Clearing a Paper JamWhen paper jams occur during scanning, use the following procedure to clear them.CAUTIONBe careful

52 Using the Scanner4. Remove the jammed document. When the jam occurred in the feed section When the jam occurred in the eject sectionIMPORTANTBe s

Using the Scanner 53Chapter 2Note• After removing the jammed paper, check to see if the last page was scanned, and then continue scanning.• If a paper

iiiInternational ENERGY STAR ProgramAs an ENERGY STAR® Partner, Canon Electronics Inc., has determined that this machine meets the ENERGY STAR® Progra

54 Using the Scanner7. Other FunctionsThis scanner also supports the scanning functions described below.Double Feed Detection Function...

Using the Scanner 55Chapter 2Skew Detection FunctionIf long documents are skewed, then they may rub against the feed slot or the edges of the feed pat

56 Using the ScannerLong Document Mode SettingsFollow the procedure below to set the long document mode.1. Use the following procedure to open the [CA

Using the Scanner 57Chapter 2 Windows XPSwitch the Control Panel to Classic View, or select [Printers and Other Hardware] in the working field. Wind

58 Using the Scanner3. Click [View devices and printers]. (For Windows XP and Windows Vista, click [Scanners and Cameras].)4. Select [CANON DR-6030C]

Using the Scanner 59Chapter 2[CANON DR-6030C USB Properties] (or [CANON DR-6030C SCSI Properties]) is displayed.2. Click the [Maintenance] tab.

60 Using the Scanner3. Click the [Long Document mode (1,000 mm)] or [Long Document mode (3,000 mm)].4. Click [OK] to change the scanner’s settings and

Using the Scanner 61Chapter 2Standby Mode SettingsThe scanner is designed to save energy by going into Standby mode if it is not used for a certain pe

62 Using the ScannerMultiStream FunctionIf the application that you are using supports the MultiStream function, then it is possible to scan a documen

Chapter 3Software SetupThis chapter explains the elements of the ISIS/TWAIN driver setup dialog boxes and describes how to make settings, using variou

INTRODUCTION 1INTRODUCTIONThank you for purchasing the Canon DR-6030C document scanner. Please read this manual thoroughly before using the machine to

64 Software Setup1. ISIS/TWAIN Driver Properties Dialog BoxThe ISIS/TWAIN driver properties dialog box consists of four tabs: Basic, Brightness, Image

Software Setup 65Chapter 3[Basic] Tab SheetThis [Basic] tab sheet is displayed when the driver is called directly and not from another settings dialog

66 Software Setup☞ Refer to the descriptions of the following function for details about “Skip Blank Page,” “Auto Color Detection,” “Detect Page Size,

Software Setup 67Chapter 3☞ Depending on the application program, operation may become unstable when [Auto Color Detection] is enabled. In that case,

68 Software SetupMode-Dependent Function LimitationsThe following tab sheet functions are partially disabled according to the selected mode. Refer to

Software Setup 69Chapter 3• When scanning a page with a dark area at the left or right edge• When scanning a glossy or reflective document• When the b

70 Software SetupThe Content density should be adjusted according to document content, so that only blank pages are skipped: increase the setting if t

Software Setup 71Chapter 3Image QualityWhen 400 or 600 dpi resolution is selected, you can enable this and select either [Speed Priority] or [Image Qu

72 Software Setup[Auto Color Detection Settings] Dialog BoxThis dialog box appears when you select [Auto Color Detection], where you can make settings

Software Setup 73Chapter 3[Scan Area] Dialog BoxIn this dialog box you can define the area of the document page to scan on a selected page size, and r

2 INTRODUCTIONSymbols Used in This ManualThe following symbols are used in this manual to explain procedures, restrictions, handling precautions, and

74 Software SetupAreaSelect the area to be scanned. ☞ Area settings here are overridden in the following cases:• When the [Auto-detection] page size i

Software Setup 75Chapter 3The availability of brightness and contrast settings are as follows according to the mode setting on the [Basic] tab sheet.✓

76 Software Setup[Enable Back Side Contrast] Check BoxIf the contrast of the front and back of the document pages is different, select this to adjust

Software Setup 77Chapter 3SelectSelect the side and color for custom setting.☞ The color bar and color of the sample image are changed to show the spe

78 Software Setup[Export] ButtonClicking this button exports the custom gamma curve settings as a gamma table file (*.pxg.)[Image processing] Tab Shee

Software Setup 79Chapter 3[Reverse Image] Check Box (TWAIN driver only)The document is scanned with black and white reversed when scanning in black an

80 Software Setup[Prevent Bleed Through / Remove Background] Check BoxSelect this to Prevent Bleed Through when scanning thin document pages and those

Software Setup 81Chapter 3☞ The color range within the shaded (cross-hatched) area is dropped out or enhanced.☞ You can move the shaded area by draggi

82 Software Setup[JPEG Transfer] Check BoxWhen this check box is selected, scanned image data is always compressed to JPEG format within the scanner f

Software Setup 83Chapter 3Feeding OptionHere you can select the feeding method for document scanning.[Standard Feeding]This feeding method is good for

Contents 3ContentsEasy Start Guide ... FoldoutINTRODUCTION ...

84 Software SetupWith the [Automatic Feeding] or [Panel Feeding] Feeding Option [Auto]Each batch of documents is saved with different file names.[Patc

Software Setup 85Chapter 3[Addon] Dialog BoxThe [Addon] dialog box opens when you click the [Addon] button on the [Others] tab. This dialog box allows

86 Software Setup[Addon] Check BoxesSelect the respective check box to enable adding text or images to the scanned image.[Text] Settings[Enable] Check

Software Setup 87Chapter 3[Date (Month/Day/Year)] abbreviation: <MDY>Inserts the date of scanning using 10 characters in Month/Day/Year format.[

88 Software Setup[Orientation]Specify the orientation for the text to be applied.☞ Text orientation relative to the feeding direction is as follows.[F

Software Setup 89Chapter 3Preview PanelThe specified content to be applied is displayed in the Preview panel.☞ You can magnify the Preview display in

90 Software Setup[Horizontal Offset]Enter the desired offset from the edge of the document feeder inlet.☞ When applying an add-on to the front side, e

Software Setup 91Chapter 3First and Second Counter Settings Dialog BoxesThese dialog boxes open when you click the respective [Change] button in the [

92 Software Setup2. Practical ExamplesThis section provides examples of settings for the DR-6030C ISIS/TWAIN driver. Refer to these examples when maki

Software Setup 93Chapter 3Scanning Non-Standard-Size Documents• To scan non-standard-size documentsIf non-standard-size documents are scanned with a s