Canon LBP-3300 Instruction Manual

Installing the Optional AccessoriesConnecting the Printer to a Computer and Installing the CAPT SoftwareConnecting the Power CordLoading PaperInstal

10 Step1 7 Remove the tape that secures the packing material in the paper cassette (2 locations). 8 Remove the packing material in the paper cassette

11 Step2 Installing the Toner Cartridge For details on handling the toner cartridge, see "Chapter 5 Routine Maintenance" in User's Gu

12Step23Hold the toner cartridge as shown in the figure, shake it gently 5 or 6 times to evenly distribute the toner inside the cartridge.IMPORTANT• I

13Step25Hold the toner cartridge properly with the arrowed side facing up as shown in the figure.6Push the toner cartridge into the printer until it to

14Step27Close the front cover.Holding the opening of the front cover, close it gently.IMPORTANT• If you cannot close the front cover, check if the ton

15Step3Loading PaperFor details on handling the manual feed slot or paper cassette, see "Chapter 2 Loading and Outputting Paper" in User&a

16Step31Pull out the paper cassette.CAUTIONBe sure to take the paper cassette out of the printer before loading paper. If paper is loaded while the pa

17Step3CAUTIONWhen loading paper, take care not to cut your hands with the edges of the paper.IMPORTANT• Be sure to check if the paper guide is at the

18Step36Set the paper cassette in the printer.Push the paper cassette into the printer firmly until the front side of the paper cassette is flush with t

19Step31Open the manual feed slot cover.2Adjust the paper guides to the width of the loaded paper as shown in the figure.The paper guides move together

2 Preface Manuals The electronic version (PDF) of the manuals is included on the CD-ROM that comes with this printer.: Guides with this symbol are P

20 Step3 3 Gently insert the paper until it touches the back of the printer while supporting the paper with hands as shown in the figure. When the pap

21Step3 Face-up Output SlotPrinted paper is output to the face-up output slot on the rear of the printer unit with the printed side facing up. The fa

22Step4Connecting the Power CordIMPORTANT• One AC power outlet should be used exclusively for the printer.• Do not plug the power plug into the auxili

23Step5Connecting the Printer to a Computer and Installing the CAPT SoftwareThis section describes the procedure for connecting the printer to a compu

24Step52Open the expansion slot cover.3Connect the B-type (square) end of the USB cable to the USB connector on the printer, then close the expansion

25Step57Click [Easy Installation] or [Custom Installation].[Easy Installation] allows you to install the printer driver and the instruction manuals si

26Step510Confirm the contents and select [I accept the terms in the license agreement], and then click [Next].11Select [Manually Set Port to Install],

27Step513The message <Installation cannot be stopped once it starts. Do you want to continue?> appears. Click [Yes].NOTE• If you are using Windo

28Step516If [Easy Installation] is selected in Procedure 7, the manuals are installed.17Confirm the installation results, then click [Next].18Select th

29Step5After Completing InstallationWhen the installation of the CAPT software is completed, an icon and folder will be created as follows. For Windo

3 Trademarks Canon, the Canon Logo, LASER SHOT, LBP, and NetSpot are trademarks of Canon Inc.Adobe, Adobe Acrobat, and Adobe Reader are trademarks of

30Step5Registering the Size of the Paper in the Paper CassetteThis printer's paper cassette cannot automatically detect the paper size. Therefore

31Step53Display the [Page Setup] sheet, then click [ ] (Display Printer Status Window) to run the Printer Status Window.NOTEFor details on the Printer

32Step5NOTEFor details on the procedure for setting the paper size switch lever, see "Chapter 2 Loading and Outputting Paper" in User&apos

33Step53Display the [Page Setup] sheet, then click [ ] (Display Printer Status Window) to run the Printer Status Window.NOTEFor details on the Printer

34Step5Configuration Page Print is printed.IMPORTANT• This is a sample of Configuration Page Print. The contents may differ from the Configuration Page P

35Step5Displaying the Manuals from CD-ROM SetupDisplay the manuals from the CD-ROM supplied with the printer.1Insert the supplied "LBP3300 User S

36Step6Installing the Optional AccessoriesInstalling the Paper FeederThe paper feeder is to be installed at the bottom of the printer unit.Make sure t

37Step6Installation SpaceThe dimensions of each part, foot positions, and the space required for using the printer with the paper feeder installed are

38Step6IMPORTANTDo not touch the black rubber pad (A) in the paper cassette. This may result in misfeeds.2Remove the tape that secures the packing mat

39Step6Moving the PrinterWhen installing the paper feeder in the printer after installing the printer, move the printer to an appropriate location tem

4IMPORTANT Water droplets (condensation) may form inside the printer under the following circumstances. Leave the printer for two hours or more to ad

40Step65Pull out the paper cassette.6Move the printer unit from the installation site.From the front side, securely hold the printer by the lift handl

41Step6• The back portion (A) of the printer is relatively heavy. Be careful not to get off-balanced when lifting the printer. If you do so, you may d

42Step6IMPORTANT• Do not touch the connector (A) in the paper feeder. This may result in damage to the printer or misfeeds.• Do not install the paper

43Step67Plug the power plug into the AC power outlet.8Connect the USB cable, then close the expansion slot cover.IMPORTANTBe sure to turn the printer

44Step6Network BoardInstall the network board in the expansion slot located on the rear of the printer.By installing the optional network board, you c

45Step6Parts and Their FunctionsaaaaPrinter ConnectorConnects to the printer. Do not touch the connector directly with yourhands.bbbbLAN ConnectorConn

46Step63Remove the power cord.If there is not enough space to install the network board, move the printer to a place where you can work easier.4Remove

47Step68Connect the LAN cable.Connect a LAN cable that is compatible with the LAN connector of the network board according to the network.9Connect the

48AppendixCD-ROM CAPT (Canon Advanced Printing Technology) software, USB class driverThe CAPT (Canon Advanced Printing Technology) software included

49● Custom InstallationClicking this button allows you to select whether to install the printer driver only or install the manuals only.● Additional S

5 Installation Space Select an installation location where you can secure the following amounts of free space around the printer, and a surface that

R-IE-699AC ©2005 CANON INC.CANON INC.30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, JapanCANON U.S.A., INC.One Canon Pl

6 Step1 Installing the Printer Confirming the Package Contents Make sure that all the following items are contained in the package before installing t

7 Step1 1 Pull out the paper cassette. 2 Carry the printer unit to the installation site. From the front side, securely hold the printer by the lift

8 Step1 • The back portion (A) of the printer is relatively heavy. Be careful not to get off-balanced when lifting the printer. If you do so, you may

9 Step1 2 Remove the tape attached to the printer (3 locations). 3 Open the manual feed slot cover. 4 Remove the tape attached to the printer (3 loca