Canon i-SENSYS LBP6650dn User Manual

LinuxUFR II/UFRII LT Printer DriverUser's GuideUSRMA-0587-05 2018-08 en Copyright CANON INC. 2018

Trademarks3FCJ-008Microsoft and Windows are either registered trademarks or trademarks of Microsoft Corporation in the UnitedStates and/or other count

● If you print from the command line without specifying the document name or user name, the name set onthe [Device Settings] sheet of the driver setti

Device Settings - Authentication Function3FCJ-029You can perform print management by means of the department ID management function or the userauthent

CNUseCSModeJobAccountSpecies the authentication method supported by the printer when the department ID management function isactivated.Mode1: Encrypt

AppendixAppendix ...

Appendix3FCJ-02AContains additional information about the printer driver, such as restrictions, etc. Main Restrictions(P. 102) Support(P. 103)Appendix

Main Restrictions3FCJ-02CThe main restrictions when using this driver are as follows.Usage Restrictions Based on CUPS Operation SettingsWhen you use C

Support3FCJ-02EThis Software and Related Information are independently developed by Canon and distributed by your Canonlocal company. Canon (as a manu

This Font Software is licensed under the SIL Open Font License,Version 1.1.This license is copied below, and is also available with a FAQ at:http://sc

1) Neither the Font Software nor any of its individual components, inOriginal or Modied Versions, may be sold by itself.2) Original or Modied Versio

About This DriverAbout This Driver ...

About This Driver3FCJ-009This driver is a Linux operating system printer driver that supports Canon devices. It uses CUPS (the CommonUNIX Printing Sys

Printing from the Command LineYou can use the lpr command to print. Built-in device functions can be specied as options.Related Topics Printing Using

Before UseBefore Use ...

Before Use3FCJ-00A● The newest driver software is posted on the Canon web site. Please verify the operating environment etc.and download the appropria

Installing the DriverInstalling the Driver ...

Installing the Driver3FCJ-00CThis section describes the method for installing and uninstalling the driver. Pre-installation Check(P. 15) Installation

Pre-installation Check3FCJ-00EThis describes what needs to be checked beforehand in order to install the driver correctly. System Requirements(P. 16)

System Requirements3FCJ-00FUse one of the following system environments with this driver.HardwareA computer running Linux that is equipped with an x86

ContentsIntroduction ...

Cautions for Installation3FCJ-00HNote the following during installation.● When installing the driver or registering a printer using the Canon Printer

About the Readme File3FCJ-00JThe Readme le describes precautions for installing and using the driver.The Readme le is saved under the following name

Installation Procedures3FCJ-00KIn order to perform printing, it is necessary to register the printer in the CUPS spooler service after installingthe d

Installing Using the Installer3FCJ-00LYou can use the installer to install a new driver.You can also update a driver that is already installed using t

Related Topics Registering a Printer(P. 25) About the Readme File(P. 18) Installing the Required Modules Individually(P. 22)Installing the Driver21

Installing the Required Modules Individually3FCJ-00RYou can use a command to install the required modules individually. Follow this procedure if you c

3Install the PPD les.Using wild cards, specify all PPD le installation packages that include drivers.# rpm –ivh cncups*4Restart CUPS.Use one of the

# service cups restartIt may be necessary to use a command for the rpm package, depending on the operating system anddistribution you are using.Regist

Registering a Printer3FCJ-00SRegister the printer to the spooler service of CUPS.Normally, the utility (Canon Printer Setup Utility) is used to regist

$ cnsetuputil2Perform one of the following operations according to the printer connection method.For network printersClick [Add] → proceed to the next

[Paper Source] Sheet ...

4Select the protocol or device URI, depending on how the printer is connected → click[Register].For network printersSelect the [lpd] or [socket] proto

If you want to register multiple printers, repeat steps 2.(P. 26) to 4.(P. 27) .5When printer registration is complete, click [Close].If printing cann

Checking the Driver Version3FCJ-00UThis section describes the procedure for using a command to check the version of a currently installed driverand PP

Overwriting the Module to Upgrade the Driver3FCJ-00WIf the installer cannot be used in your environment, overwrite the module to update the installed

3Install the printer driver module.For 32-bit environments# rpm -Uvh cndrvcups-ufr2-uk-x.xx-1.i386.rpmFor 64-bit environments# rpm -Uvh cndrvcups-ufr2

# dpkg -i cndrvcups-common_x.xx-1_i386.debFor 64-bit environments# dpkg -i cndrvcups-common_x.xx-1_amd64.deb3Install the printer driver module.For 32-

# /usr/sbin/lpadmin -x [printer name]2Uninstalling a Driver(P. 34)3Installing the Required Modules Individually(P. 22)If the printer was already regis

Uninstalling a Driver3FCJ-00XThis section describes the procedure for uninstalling an unnecessary driver. It is necessary to uninstall thedriver after

For Debian Type Distributions1Delete the registered printer.(1) Start the Canon Printer Setup Utility by performing one of the following operations. -

PrintingPrinting ...

IntroductionIntroduction ...

Printing3FCJ-00YThis section describes the printing method using the driver. Printing Using the Driver UI(P. 38) Printing from an Application(P. 40) P

Printing Using the Driver UI3FCJ-010When editing default settings and performing printing using the driver UI, use the cngplp command.Specifying defau

NOTE● When you nish specifying the settings by clicking the [Print] button, those settings are available onlyfor the current print job.● When you ni

Printing from an Application3FCJ-011When printing from an application, edit the print settings in the print settings dialog box displayed by theapplic

Registering the Printer with OpenOce 1.xx3FCJ-0121On the Start menu, point to [Program] - [Oce], and then select [OpenOce PrinterAdministration].Th

Registering the Printer with GIMP 2.x3FCJ-0131Start GIMP, and then display the print dialog box by right-clicking on an image to beprinted, and select

Printing from an Application3FCJ-014The procedures and menus described below may differ depending on the application you use. This sectiondescribes th

Functions Not Available from Applications3FCJ-015The following functions cannot be set from the print settings dialog box displayed from applications.

Outputting PostScript Files from an Application3FCJ-016When you want to perform printing using functions that cannot be used from an application (see

Caution When Printing from Applications3FCJ-017This section describes problems that may occur when printing from applications, and how to avoid them.

Introduction3FCJ-000 How to Use the Manual(P. 3) Disclaimers(P. 5) Copyright(P. 6) Trademarks(P. 7)Introduction2

2Enter the following command from the command line to start the driver UI:$ cngplp -p [PostScript filename].psThe [cngplp] dialog box is displayed.3Se

From the Driver UI1Enter the cngplp command from the command line with user privileges.2Select the printer you are using in the [cngplp] dialog box →

3click [Device Settings], and Select [Job Accounting].4Click [Settings].The [ID/PIN Settings] dialog box is displayed.5Enter the ID and PIN → click [O

From the Driver UI1Enter the cngplp command from the command line with administrator privileges.2Select the printer you are using in the [cngplp] dial

Cautions When Printing a PostScript File From theDriver UI3FCJ-018If you print a PostScript le output from an application with the driver UI, the pri

Printing from the Command Line3FCJ-019In the command line mode, various printer driver parameters can be specied from the command line withoutusing t

Settings ListSettings List ...

Settings List3FCJ-01AThis section describes the settings for printing from the driver settings screen. [cngplp] Screen(P. 55) [General] Sheet(P. 56) [

[cngplp] Screen3FCJ-01CYou can select the printer to use for printing and specify the basic print functions.[Name]Select the printer to use for printi

[General] Sheet3FCJ-01EYou can set the paper size, print layout, and brightness, etc.[Page Size]Species the paper size to print on.[Orientation]Speci

How to Use the Manual3FCJ-001This explains things that you need to know in order to use this manual. Notations Used in the Manual(P. 4)Introduction3

[Finishing] Sheet3FCJ-01FYou can set the print layout and output method, etc.[Print Style]Select [1-sided Printing], [2-sided Printing], or [Booklet P

[Rotate]Rotates and outputs each stack at 90 degrees.[Fold]Outputs pages folded into one of a variety of forms.C-fold Z-fold [Half Fold] (SaddleFold)A

[Transparency Printing]Select the print method according to the projector that will be used.[Special Print Mode]Improves the problem where black strea

[Mode 3]Smooths dense letters and lines over halftone backgrounds.[Mode 4]Smooths the contours of large text and thick lines when they are jagged.[Mod

[Paper Source] Sheet3FCJ-01HYou can set the paper type and paper source.[Select by]/[Paper Source]/[Paper Type]Species the paper to print on by paper

[Quality] Sheet3FCJ-01JYou can adjust the color, toner, and print processing method.[Resolution]Select the print resolution.[Color Mode]Switches betwe

[Toner Volume Adjustment]Adjusts the amount of toner to match the content of the print data.For data that contains many graphics or computer graphics

[Device Settings] Sheet3FCJ-01KYou can congure print options and administrator settings.[Output Method]Enables you to switch the method for outputtin

[Do Not Use Job Accounting When B&W Printing]If you are using the department ID management function, selecting the [Quality] sheet > [Color Mod

Command ListCommand List ...

Notations Used in the Manual3FCJ-003This explains symbols and settings used in this manual.Symbols Used in This ManualIn this manual, explanations of

Command List3FCJ-01LThis section describes the options for printing from the command line. Command Format(P. 68) Basic Settings(P. 69) Finishing - 1-s

Command Format3FCJ-01RThis section describes the notation used for the format of the list of commands.Format[ ]Indicates optional options. Can be omit

Basic Settings3FCJ-01SYou can set the number of copies to be printed and paper to use.Formatlpr <le path>-o CNCopies=<Number of Copies>-o

Finishing - 1-sided/2-sided Printing3FCJ-01UYou can switch between one-sided printing and two-sided printing. You can also adjust margins.Formatlpr &l

Finishing - Paper Output Method3FCJ-01WYou can set the method for sorting and processing output paper.Formatlpr <le path>-o Collate={{True | Fa

PUNU23: 2/3 HolesPUNF2: 2 Holes (French)PUNF4: 4 Holes (French)PUNS4: 4 Holes (Swedish)PUNM: Multi HolesNOTE● If Off is specied for the CNMultiPunch

Finishing - Paper Output Destination3FCJ-01XYou can set a printed paper output destination.Formatlpr <le path>-o OutputBin=<Paper Output>

TrayUpperLeft: Tray (Upper Left)TrayLowerLeft: Tray (Lower Left)Bin<NUM>: Bin (where <NUM> indicates the number)Stack: StackerStackerAOutT

FinV1(SFinV2)_PBA1: Finisher-V1/V1L (V2/V2L) + Perfect Binder-A1SFinV2: Finisher-V2/V2LFinW1(SFinW2): Finisher-W1(2)FinX1: Finisher-X1FinY1(SFinY2): F

IFINH1: Inner Finisher-H1IFINH1CT: Inner Finisher-H1 + Copy TrayIFINJ1: Inner Finisher-J1Staple FinisherStFinA1: Staple Finisher-A1STFINAA1: Staple Fi

Disclaimers3FCJ-006The information in this document is subject to change without notice.CANON INC. MAKES NO WARRANTY OF ANY KIND WITH REGARD TO THIS M

BFING1: Booklet Finisher-G1BFINJ1: Booklet Finisher-J1BFINK1: Booklet Finisher-K1BFINL1: Booklet Finisher-L1BFINM1: Booklet Finisher-M1BFINN1: Booklet

Finishing - Booklet Printing3FCJ-01YYou can print with the pages of a document arranged so that the paper can be folded in half to create a booklet.To

ExampleTo print the le "sample.txt" with the following setting:● Book Opening: Left Binding● Half Fold: Use● Trim: Use● Adjust Trim Width b

Finishing - Paper Folding3FCJ-020You can output pages folded into one of a variety of forms.You can also use an option to specify the folding directio

CNAccordionZfoldingPerforms accordion Z-folding.pattern1: Portraitpattern2: LandscapeCNDoubleParallelFoldingPerforms double parallel folding.pattern1:

Finishing - Special Print Processing3FCJ-021You can set the print processing method when you want to improve the print result or use special paper.Spe

CNSpecialPrintAdjustmentAImproves the problem where black streaks appear in the printed output by thinning out the dots by usingthe Special Print Adju

CNShiftFrShortEdge option: Short Edge (Front Side)CNShiftBkLongEdge option: Long Edge (Back Side)CNShiftBkShortEdge option: Short Edge (Back Side)Exam

Finishing - Secure Printing3FCJ-022You can embed a watermark or tracking information, etc. when printing to prevent leaks of condentialdocuments.Form

Paper Source - Paper Source/Paper Type3FCJ-023You can set the paper to print on by paper source or paper type.Formatlpr <le path>-o InputSlot=&

Copyright3FCJ-007Copyright CANON INC. 2018No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, ortra

Recycled PaperRECYCLED / RECYCLED1 / RECYCLED2 / RECYCLED3 / RECYCLED4Color PaperCOLOR / COLOR1 / COLOR2Bond PaperBOND / BOND1 / BOND2 / BOND3Heavy Pa

$ lpr sample.txt -o MediaType=OHP -o CNInterleafSheet=True -o CNInterleafMediaType=PlainPaper -oCNInterleafPrint=TrueCommand List88

Paper Source - Front/Back Cover3FCJ-024You can insert a cover and back cover. You can select the side to print on and the paper source for each.Format

● Paper Source: Cassette 2$ lpr sample.txt -o CNSetFrontSheet=True -o CNFrontPrintOn=BothSides -o CNFrontPaperSrc=Cas2Command List90

Quality - Color Adjustment3FCJ-025You can switch between color printing and black-and-white printing. You can also adjust colors.Formatlpr <le pat

● Color to Use with Black: Red$ lpr sample.txt -o CNNumberOfColors=TwoColors -o CNColorToUseWithBlack=RedCommand List92

Quality - Image Processing3FCJ-026You can set the processing to perform, such as smoothing and sharpness.Specify a function supported by the model you

CNSharpness / CNHyperSharpnessStrengthens and blurs the contours of text and images by using the Sharpness function or Sharpness (Photo)function.The C

Quality - Toner Adjustment3FCJ-027You can adjust the toner density and volume.Specify a function supported by the model you are using.Formatlpr <l

Device Settings - Output Method3FCJ-028You can switch the method for outputting print data.When data is saved to the printer, it can be operated from