Canon imagePROGRAF iPF6450 User Manual Page 115

  • Download
  • Add to my manuals
  • Print
  • Page
    / 159
  • Table of contents
  • TROUBLESHOOTING
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 114
Cause Corrective Action
You are printing on heavyweight paper or
paper that curls or wrinkles easily after ab-
sorbing ink.
(See "Troubleshooting Paper Abrasion and Blurry Images.") →User's Guide
When printing on CAD Tracing Paper or other film-based media, choose a VacuumStrngth
setting of Standard, Strong, or Strongest in the Control Panel menu. If rubbing still occurs,
in the Control Panel menu, use a higher Head Height setting.
(See "Adjusting the Vacuum Strength.") →User's Guide
(See "Troubleshooting Paper Abrasion and Blurry Images.") →User's Guide
The Ejection Guide is soiled. Clean the Ejection Guide.
(See "Cleaning the Printer Exterior.") →User's Guide
The surface of the paper is dirty
The surface of the paper is dirty
Cause Corrective Action
The Paper Retainer is soiled. Clean the Paper Retainer.
(See "Cleaning Inside the Top Cover.") →P.51
You are using a paper that does not
dry easily.
In the Control Panel menu, set Roll DryingTime to at least 1 min.
(See "Menu Settings.") →User's Guide
When paper that does not dry easily is used for printing, it may curl during printing and touch the
Output Tray.
In this case, in the Control Panel menu, complete the settings for Dry time and Area in Scan Wait
Time.
However, note that printing will now take longer.
(See "Menu Settings.") →User's Guide
The optional Spectrophotometer
Unit is dirty.
Clean the Paper presser.
(See "Cleaning the Spectrophotometer Unit (option) Parts.") →P.54
The back side of the paper is dirty
The back side of the paper is dirty
Cause Corrective Action
The Platen has become dirty after borderless printing or printing on
small paper.
Open the Top Cover and clean the Platen.
(See "Cleaning Inside the Top Cover.") →P.51
The Platen suction is too strong. In the Control Panel menu, reduce the level of VacuumStrngth.
(See "Adjusting the Vacuum Strength.") →User's Guide
BordlessOversize is set to Standard in the Control Panel menu. Set BordlessOversize to Little in the Control Panel menu.
(See "Menu Settings.") →User's Guide
Roller marks are left across the trailing edge of paper
Roller marks are left across the trailing edge of paper
Cause Corrective Action
The paper was removed without pressing the OK button
after printing from the Front Paper Feed Slot.
Following the instructions displayed, press the OK button, and after removing
the paper, press the OK button again.
Wipe the rollers to clean them.
(See "Cleaning Inside the Top Cover.") →P.51
(See "Cleaning the Paper Retainer.") →User's Guide
Immediately after borderless printing, the trailing edge margin is soiled during regular printing
Immediately after borderless printing, the trailing edge margin is soiled during regular printing
Cause Corrective Action
Depending on your printing environment, after bor-
derless printing in which the leading and trailing edge
of the roll is cut automatically, any ink adhering to the
cutter unit may rub off on the next printed document.
Follow these steps to change the Between Pages setting of Drying Time to a val-
ue between about 30 seconds and 3 minutes before trying borderless printing
again.
1.
On the Main sheet of the printer driver, click Advanced Settings by Media
Type.
2.
Select an ink drying time in the list for the Between Pages setting of Drying
Time.
iPF6450
The surface of the paper is dirty
Basic Guide
Troubleshooting Problems with the printing quality
115
Page view 114
1 2 ... 110 111 112 113 114 115 116 117 118 119 120 ... 158 159

Comments to this Manuals

No comments