Canon imageRUNNER LBP5360 User's Guide Page 334
- Page / 444
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
8-37
Troubleshooting
8
Message List
Remedy 2 Perform a soft reset using the RESET menu, increase the free space of RAM
using the following procedure, register the data again, and then print again.
• Perform a hard reset or cycle the power of the printer (Be aware that all the
data in the memory will be deleted).
• Install an optional expansion RAM module. (See "Installing RAM," on p. 9-15)
<26 SYS.MEM.FULL> <Auto Error Skip>
Cause The work memory required for the printer process has run out while the system
is processing the data (mainly the graphics data and text data).
Remedy 1 The printer continues printing by pressing [Online]. However, the data with
which an error has occurred is not printed properly.
Remedy 2 Perform a soft reset using the RESET menu, and then increase the free space
of RAM using the following procedure.
• Perform a hard reset or cycle the power of the printer (Be aware that all the
data in the memory will be deleted).
• Install an optional expansion RAM module. (See "Installing RAM," on p. 9-15)
<27 JOB START ERR> <Auto Error Skip>
Cause The specified emulation does not exist.
Remedy Press [Online] to continue printing from the next data. However, the data with
which an error has occurred is not printed.
<30 MEMORY FULL> <Auto Error Skip>
Cause 1 The work memory has run out while the system is processing the data.
Remedy The printer continues printing by pressing [Online]. However, the data with
which an error has occurred may not be printed properly.
Cause 2 (If this error has occurred while the printer is ON) The amount of memory
specified in NVRAM could not be secured because the memory construction
had been changed (The expansion RAM is removed).
Remedy 1 The printer continues printing by pressing [Online]. However, the data may not
be printed properly due to the change of the memory construction.
IMPORTANT
The memory construction of NVRAM is rewrote to a securable value when <30
MEMORY FULL> appears. (* The settings for RIP Once and the hard disk is restored to
the default value.) (See "SETUP Menu Settings," on p. 6-13)
- User's Guide 1
- Laser Printer 2
- Manuals for the Printer 3
- How This Manual Is Organized 4
- Contents 5
- Chapter 3 Using the Printer 7
- Chapter 10 Appendix 10
- How To Use This Manual 11
- Legal Notices 13
- Laser Safety 14
- WEEE Directive 16
- License Notice 16
- Trademarks 16
- Copyright 17
- Disclaimers 18
- Use of Images 19
- Installation 20
- Power Supply 22
- Handling 23
- Maintenance and Inspections 24
- Consumables 26
- Before You Start 28
- Features and Benefits 29
- Features and Benefits 30
- ■ Typefaces 31
- ■ Remote UI Support 31
- User Manual CD-ROM Menu 32
- Using The CD-ROM Menu 33
- Parts and Their Functions 34
- Rear View 35
- Inner View 36
- Control Panel 37
- 00 READY LT 39
- CONTROL MENU 39
- Optional Accessories 40
- Expansion RAM 41
- Hard Disk 42
- Installing the Printer 44
- Installation Procedure 45
- Installation Site 46
- Power Supply Requirements 47
- Installation Requirements 47
- Installation Space 48
- Foot Positions 49
- Precautions for Handling 50
- Install the output tray 56
- Loading Paper 68
- Connecting the Cables 69
- Connecting to a Computer 71
- ● Installing the Software 72
- Using a USB Cable 73
- Using a Printer Cable 75
- Operation 76
- Registering a Paper Size 77
- Specifying a Paper Type 78
- Press [Utility] 79
- Press [OK] 79
- Turning the Printer OFF 83
- When Not Using a Hard Disk 84
- Online and Offline 92
- Placing the Printer Offline 93
- Printing/Saving Jobs 94
- ■ [Store] Mode 95
- ■ [Interrupt] Mode 95
- ■ [Edit and Preview] Mode 95
- Encrypted Secured Print) 96
- [] and [ ] 98
- ListFile.doc 100
- Canceling a Job 101
- Canceling a Job (Cancel Job) 102
- Press [Reset] 103
- Using the Printer 105
- Loading and Outputting Paper 106
- Paper Requirements 107
- Paper Type 108
- ■ Plain Paper 109
- ■ Heavy Paper 109
- ■ Transparency 110
- ■ Coated Paper 110
- ■ Envelope 110
- Printable Area 112
- Unusable Paper 113
- Storing Paper 114
- Storing Printouts 115
- Paper Source 116
- Paper Source Type 117
- Selecting a Paper Source 118
- Cassette 119
- Output Tray 120
- Precautions on Loading Paper 123
- 11 NO LT PAPER PC LOAD LT 124
- Pull out the paper cassette 125
- Press [Settings] 137
- Press [Settings] 139
- Open the multi-purpose tray 142
- Pull out the auxiliary tray 143
- When Loading Envelopes 148
- 2-sided Printing 158
- 1-sided Printing 159
- Printing 160
- Manual 2-sided Printing 161
- The Printing Environment 166
- Menu Functions 167
- Setting Priority 168
- Menu Categories 168
- How to Use the Operation Keys 170
- How to View the Display 172
- POWER SAVE MODE 173
- =ON 173
- SETUP Menu 174
- UTILITY Menu 176
- JOB Menu 177
- RESET Menu 178
- CANCEL JOB Menu 179
- SELECT FEEDER Menu 180
- EXEC 181
- Initializing the SETUP Menu 182
- Printing Environment Settings 184
- Setting Items 185
- ■ LAYOUT MENU Options 187
- ■ QUALITY MENU Options 188
- SETUP Menu Settings 196
- PWR SAVE IN ERR 197
- POWER SAVE TIME 197
- WARNING STEP 197
- AUTO ERROR SKIP 198
- PANEL LANGUAGE 198
- SHOW WARNINGS 198
- DATE AND TIME 199
- TIMER SETTINGS 200
- ■ WAKE UP TIME 201
- ■ POW. SAVE TIMER 201
- HARD DISK 202
- INTERRUPT PRINT 203
- SECURING TIME 203
- SECURED TYPE 204
- RIP ONCE 204
- FEEDER MENU Options 205
- CASSETTE(n) SIZE (n = 1, 2) 206
- STD PAPER SIZE 207
- TRAY PRIORITY 208
- INVLDPAPER TRAY 209
- AUTO SELECTION 209
- STD PAPER TYPE 210
- TRAY PAPER TYPE 210
- CASSETTE(n) TYPE (n = 1, 2) 212
- MANUAL 2-SIDED 213
- 2-SIDED PRINT 213
- + direction 214
- BIND.LOCATION 215
- Center Center Center 216
- ALT.METHOD 217
- QUALITY MENU Options 218
- DENSITY: CYAN 219
- DENSITY: MAGENTA 220
- DENSITY: YELLOW 220
- DENSITY: BLACK 220
- COLOR MODE 221
- HALFTONES 221
- GRAY COMPENSATE 222
- ■ CMS SELECTION 223
- ■ CMS/GAMMA 223
- ■ RGB SRCE PROF 224
- ■ OUTPUT PROFILE 225
- ■ MATCHING METHOD 225
- QUALITY CHANGE 227
- INTERFACE MENU Options 228
- NETWORK MENU 230
- SERVER is set to ON 231
- ■ SPOOLER 232
- ■ START WAIT TIME 232
- ■ REMOTE UI SET 232
- ■ ETHERNET DRIVER 232
- EXT.I/F MENU 233
- CONNECT.RECOG 233
- USER MAIN. Options 234
- RECVRY PRINTING 235
- SPECIAL MODE J 235
- SUBSTITUTE SIZE 236
- SP.IMAGE MODE 236
- HDD MAINTENANCE 237
- SP.PRINT MODE 238
- PCL SETUP Options 239
- Feeding direction 240
- FORM LINES 241
- SYMBOL SET 241
- CUSTOM SIZE 241
- UNIT OF MEASURE 241
- X DIMENSION 242
- Y DIMENSION 242
- APPEND CR TO LF 242
- ENLRG A4 WIDTH 243
- UFR II SETUP Options 244
- UTILITY Menu Settings 245
- CLEANING 246
- NW STATUS PRINT 246
- EXT.I/F PRINT 246
- CALIBRATION 246
- PRNTPOSNPRINT 247
- JOB Menu Settings 248
- SECURED PRINT 249
- STOREJOB LIST 250
- STOREJOB PRINT 250
- JOB LOG LIST 251
- STORE LOG LST 251
- REPORTLOG LST 251
- RESET Menu Settings 252
- SHUT DOWN 253
- SELECT FEEDER Menu Settings 254
- TRAY PAPER SIZE 255
- Routine Maintenance 258
- 16 PREP.X TNR 259
- 16 CHG.X TNR 259
- 9G CHK X TNR 259
- 1G CHG.X TNR 259
- Replacing a Toner Cartridge 260
- Open the front cover 262
- Remove the paper 272
- Close the front cover 272
- Storing Toner Cartridges 275
- Cleaning the Fixing Roller 276
- Press [Feeder Selection] 278
- 0.20 in. (5 mm) 280
- 0.39 in. (10 mm) 280
- Press [Online] 281
- Moving the Printer 287
- Connect the USB cable 294
- Handling the Printer 295
- Troubleshooting 298
- Printing is 299
- Paper Jams 301
- Paper Jam Area 304
- 13 PAPER JAM 305
- FRONT COVER 305
- Open the top cover 312
- Close the top cover 318
- Disappear 319
- , pull out the jammed paper 322
- as shown 322
- Install the fixing unit 323
- Turn the printer ON 323
- Install the duplex unit 328
- Message List 330
- Ennn-nnnn 344
- E001-nnnn 344
- E003-nnnn 344
- F9-nn PWR OFF>ON 344
- Print Quality Problems 353
- Adjusting the Color Balance 363
- Installing the Paper Feeder 367
- Installing RAM 380
- Remove the rear cover 382
- Remove the three screws 382
- Remove the slot cover 383
- A standard RAM is installed 384
- Never remove the RAM 384
- Installing a Hard Disk 387
- ROM slot (white) 392
- Do not install RAM or 392
- ROM in this slot 392
- Insert the connector cable 394
- IMPORTANT 396
- Appendix 402
- Configuration Page 403
- Network Status Print 404
- PCL Fonts List 405
- Typeface Samples 406
- Bitmapped Fonts (PCL) 408
- Symbol Sets Supported 409
- ■ Roman-9 (4U) 410
- ■ ISO 8859/1 Latin 1 (0N) 410
- ■ ISO 8859/2 Latin 2 (2N) 411
- ■ ISO 8859/9 Latin 5 (5N) 411
- ■ ISO 8859/15 Latin 9 (9N) 412
- ■ PC-8, Code Page 437 (10U) 412
- ■ PC-850, Multilingual (12U) 413
- ■ PC-852, Latin 2 (17U) 414
- ■ PC-Turkish (9T) 415
- ■ Windows 3.1 Latin 1 (19U) 415
- ■ Windows 3.1 Latin 2 (9E) 416
- ■ Windows 3.1 Latin 5 (5T) 416
- ■ DeskTop (7J) 417
- ■ PS Text (10J) 417
- ■ Ventura International (13J) 418
- ■ Ventura US (14J) 418
- ■ Microsoft Publishing (6J) 419
- ■ Math-8 (8M) 419
- ■ PS Math (5M) 420
- ■ Ventura Math (6M) 420
- ■ PI Font (15U) 421
- ■ Legal (1U) 421
- ■ Windows 3.0 Latin 1 (9U) 422
- ■ ISO 8859/10 Latin 6 (6N) 422
- ■ PC-775 (26U) 423
- ■ PC-1004 (9J) 423
- ■ Windows Baltic (19L) 424
- ■ MC Text (12J) 424
- ■ Symbol (19M) 425
- ■ Wingdings (579L) 425
- ■ Dingbats (14L) 426
- ■ PC-860 Portugal (20U) 426
- ■ PC-865 Norway (25U) 427
- ISO Substitution Tables 428
- ■ ISO 11: Swedish (0S) 429
- ■ ISO 21: German (1G) 430
- ■ ISO 69: French (1F) 430
- ■ ISO 15: Italian (0I) 431
- ■ ISO 17: Spanish (2S) 431
- Specifications 432
- Controller Specifications 435
- Software Specifications 436
- Dimensions of Each Part 437
- Front Surface 438
- Numerics 439
Related products and manuals for Laser/LED printers Canon imageRUNNER LBP5360
Laser/LED printers Canon LBP-1120 User's Guide
(192 pages)
(192 pages)
Laser/LED printers Canon LBP-810 User Manual
(198 pages)
(198 pages)
Laser/LED printers Canon LBP-810 User Manual
(188 pages)
(188 pages)
Prodotti e manuali riguardandi Strumenti musicalo Yamaha YT100
Strumenti musicalo Yamaha AW1600 Manuale Utente
(218 pagine)
(218 pagine)
Strumenti musicalo Yamaha n8 Manuale Utente
(66 pagine)
(66 pagine)
Strumenti musicalo Yamaha RX-V559 Manuale Utente
(118 pagine)
(118 pagine)
Strumenti musicalo Yamaha dd65 Manuale Utente
(60 pagine)
(60 pagine)
Strumenti musicalo Yamaha dtxp4 Manuale Utente
(52 pagine)
(52 pagine)
Strumenti musicalo Yamaha Horn Manuale Utente
(21 pagine)
(21 pagine)
Strumenti musicalo Yamaha DTXT3 Manuale Utente
(160 pagine)
(160 pagine)
© 2020, manymanuals.com. All rights reserved. | 0.273 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals